Standard Products
RadHard Eclipse FPGA Family (6250 and 6325)
Data Sheet
August 22, 2006
www.aeroflex.com/RadHardFPGA
FEATURES
0.25µm, five-layer metal, ViaLink
TM
epitaxial CMOS
process for smallest die sizes
One-time programmable, ViaLink technology for
personalization
150 MHz 16-bit counters, 150 MHz datapaths, 60+ MHz
FIFOs
2.5V core supply voltage, 3.3V I/O supply voltage
Up to 320,000 usable system gates (non-volatile)
I/Os
- Interfaces with 3.3 volt
- PCI compliant with 3.3 volt
- Full JTAG 1149.1 compliant
- Registered I/O cells with individually controlled enables
Radiation-hardened design; total dose irradiation testing to
MIL-STD-883 Test Method 1019
- Total-dose: 300 krad(Si)
- SEL Immune: >120MeV-cm
2
/mg
- LET
TH
(0.25) MeV-cm
2
/mg:
>42 logic cell flip flops
>64 for embedded SRAM
- Saturated Cross Section (cm2) per bit
5.0E-7 logic cell flip flops
2.0E-7 embedded SRAM
Up to 24 dual-port RadHard SRAM modules, organized in
user-configurable 2,304 bit blocks
- 5ns access times, each port independently accessible
- Fast and efficient for FIFO, RAM, and initialized RAM
functions
100% routable with 100% utilization and 100% user fixed
I/O
Variable-grain logic cells provide high performance and
100% utilization
Comprehensive design tools include high quality Verilog/
VHDL synthesis and simulation
QuickLogic IP available for microcontrollers, DRAM
controllers, USART and PCI
Packaged in a 208-pin CQFP, 288 CQFP, 484 CCGA, and
484 CLGA,208 PQFP, 280 PBGA, 484 PBGA
Standard Microcircuit Drawing 5962-04229
- QML qualified
INTRODUCTION
The RadHard Eclipse Field Programmable Gate Array Family
(FPGA) offers up to 320,000 usable system gates including
Dual-Port RadHard SRAM modules. It is fabricated on 0.25µm
five-layer metal ViaLink CMOS process and contains a
maximum of 1,536 logic cells and 24 dual-port RadHard SRAM
modules (see Figure 1 Block Diagram). Each RAM module has
2,304 RAM bits, for a maximum total of 55,300 bits. Please
reference product family comparison chart on page 2.
RAM modules are Dual Port (one asynchronous/synchronous
read port, one write port) and can be configured into one of four
modes (see Figure 2). Designers can cascade multiple RAM
modules to increase the depth or width allowed in single
modules by connecting corresponding address lines together and
dividing the words between modules (see Figure 3). This
approach allows a variety of address depths and word widths to
be tailored to a specific application.
The RadHard Eclipse FPGA is available in a 208-pin Cerquad
Flatpack, allowing access to 99 bidirectional signal I/O, 1
dedicated clock, 8 programmable clocks and 16 high drive
inputs. Other package options include a 288 CQFP, 484 CCGA
and a 484 CLGA.
Aeroflex uses QuickLogic Corporation’s licensed ESP
(Embedded Standard Products) technology. QuickLogic is a
pioneer in the FPGA semiconductor and software tools field.
1
PRODUCT DESCRIPTION
I/O Pins
(9:0)
(17:0)
WA
WD
WE
WCLK
(1:0)
MODE
RE
RCLK
RA
RD
ASYNCRD
(9:0)
(17:0)
• Up to 310 bi-directional input/output pins, PCI-compliant for
3.3V buses (see Table 4)
• Each bidirectional I/O contains RadHard flip-flops for input,
output, and output enable lines
Distributed Networks
• One, dedicated clock network, hardwired to each logic cell
flip-flop clock pin to minimize skew
• Eight programmable clock networks, accessible from clock
pins or internal logic
Figure 2. RadHard Eclipse FPGA RAM
Software support for the product is available from QuickLogic.
The turnkey QuickWorks
TM
package provides the most com-
plete software solution from design entry to logic synthesis,
place and route, simulation, static timing, and power analysis.
The QuickTools
TM
for Workstations package provides a solu-
tion for designers who use Cadence, Exemplar, Mentor, Synop-
sys, Synplicity, Viewlogic, Veribest or other third-party tools
for design entry, synthesis, simulation. Please visit Quick Log-
ic’s website at www.quicklogic.com for more information.
The variable grain logic cell features up to 17 simultaneous in-
puts and 6 outputs within a cell that can be fragmented into 6
independent sections. Each cell has a fan-in of 30 including
register and control lines (see Figure 5).
• 20 pre-defined Quad-clock networds, five per quadrant. Ac-
cessed by the 8 programmable global clock networks
• Sixteen high drive inputs. Two inputs located in each of the
eight I/O banks. Used as clock or enable signals for the I/O
RadHard flip-flops, or as high drive inputs for internal logic
Performance
• Input + logic cell + output total delays under 12ns
• Data path speeds over 200 MHz
• Counter speeds over 150 MHz
• FIFO speeds over 60+ MHz
WDATA
RAM
Module
(2,304 bits)
RDATA
WADDR
RADDR
RAM
Module
(2,304 bits)
WDATA
RDATA
Figure 3. RadHard Eclipse FPGA Module Bits
4
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
