The UT54ACS165E is an 8-bit serial shift register that, when clocked,
shifts the data toward serial output Q
H
. Parallel-in access to each stage
is provided by eight individual data inputs that are enabled by a low
level at the SH/LD input. The devices feature a clock inhibit function
and a complemented serial output Q
H
.
Clocking is accomplished by a low-to-high transition of the CLK input
while SH/LD is held high and CLK INH is held low. The functions of
the CLK and CLK INH (clock inhibit) inputs are interchangeable.
Since a low CLK input and a low-to-high transition of CLK INH will
also accomplish clocking, CLK INH should be changed to the high
level only while the CLK input is high. Parallel loading is disabled
when SH/LD is held high. Parallel inputs to the registers are enabled
while SH/LD is low independently of the levels of CLK, CLK INH or
SER inputs.
The device is characterized over the full military temperature range of
-55°C to +125°C.
Note:
1. Q
n
= The state of the referenced output one setup time prior to the Low-to-
High clock transition.
LOGIC SYMBOL
(1)
SH/LD
(15)
CLK INH
(2)
CLK
(10)
SER
(11)
A
(12)
B
(13)
C
(14)
D
(3)
E
(4)
F
(5)
G
(6)
H
SRG8
C1 (LOAD)
≥1
C2/
PINOUT
16-Lead Flatpack
Top View
SH/LD
CLK
E
F
G
H
Q
H
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
CLK INH
D
C
B
A
SER
Q
H
2D
1D
1D
1D
(9)
Q
(7)
H
Q
H
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
1
LOGIC DIAGRAM
A
(11
)
SH/LD
B
(12)
C
(13)
D
(14)
E
(3)
F
(4)
G
(5)
H
(6)
(1)
CLK INH
CLK
(15)
(2)
S
C
SER
S
C
D Q
B
S
C
DQ
C
S
C
D Q
D
S
C
D Q
E
S
C
D Q
F
S
C
D Q
G
S
C
(9)
Q
H
(10
)
D
Q
A
(7)
D Q
H
R
R
R
R
R
R
R
R
Q
H
RADIATION HARDNESS SPECIFICATIONS
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
2
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+ .3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these
or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods
may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
3.0 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS FOR THE UT54ACS165E
7
( V
DD
= 3.0V to 5.5V; V
SS
= 0V
6
; -55°C < T
C
< +125°C)
SYMBOL
V
IL
Description
Low-level input voltage
1
High-level input voltage
1
CONDITION
VDD
3.0V
5.5V
V
IH
3.0V
5.5V
I
IN
V
OL
Input leakage current
Low-level output voltage
3
High-level output voltage
3
Short-circuit output current
2 ,4
V
IN
= V
DD
or V
SS
I
OL
= 100µA
5.5V
3.0V
4.5V
V
OH
I
OH
= -100µA
3.0V
4.5V
I
OS
V
O
= V
DD
and V
SS
3.0V
5.5V
I
OL
Low level output current
9
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
I
OH
High level output current
9
V
IN
= V
DD
or V
SS
V
OH
= V
DD
-0.4V
P
total
I
DDQ
C
IN
C
OUT
Power dissipation
2, 8
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
C
L
= 50pF
V
IN
= V
DD
or V
SS
ƒ
= 1MHz
ƒ
= 1MHz
3.0V
5.5V
3.0V
5.5V
5.5V
3.0V
5.5V
0V
0V
2.75
4.25
-100
-200
6
8
-6
-8
2.9
1.16
10
15
15
mW/
MHz
µA
pF
pF
mA
100
200
mA
mA
2.1
3.85
-1
1
0.25
0.25
V
µA
V
MIN
MAX
0.9
1.65
V
UNIT
V
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤5.0E5
amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765pF/
MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si) per MIL-STD-883 Method 1019 Condition B.
8. Power dissipation specified per switching output.
9. This value is guaranteed based on characterization data, but not tested.
I would like to ask you guys, I am just learning about microcontrollers, and I want to buy a suitable board on Taobao, do you have any recommendations?...
I have installed evc++4.0+sp3 and pocket pc 2003sdk English version on my computer. After writing an evc basic database program, the problem when compiling is: fatal error C1083: Cannot open precompil...
Qorvo recently announced a motor control reference design that integrates the PAC5556 smart motor controller with Qorvo’s new silicon carbide (SiC) FETs into a proof-of-concept system-on-chip (SoC) to...
I checked a lot on the Internet; many people said that it would be easy to use after downloading it, but it was useless. I will write this for myself to read later. It is not very standardized and is ...
On August 22nd, Lantu Motors unveiled a new technology called "Lanhai Intelligent Hybrid" during a live broadcast of CCTV News' "Top Laboratory." The name sounds like another new term, but a closer...[Details]
SMT placement machines are important equipment in surface mount technology (Surface Mount Technology). Their performance has a decisive impact on the quality and efficiency of electronic manufactur...[Details]
Reflow soldering, as an electronics assembly process, has become a vital component of the electronics manufacturing industry. Choosing reflow soldering equipment is crucial for improving production...[Details]
Shenzhen Baowei Power Supply high frequency pure sine wave power, communication inverter power supply has two communication interfaces, RS232 and R485 interfaces, their functions and characteristic...[Details]
With the gradual popularization of new energy vehicles in recent years, more and more people have been able to access and purchase electric vehicles. The structure of electric vehicles is composed ...[Details]
Civilian internal combustion engines operate in the range of approximately 1000-4000 rpm. This results in the engine's kinetic energy being ineffective at low or high rpm, making starting difficult...[Details]
The screen is the first thing you notice when evaluating a phone's quality. Its quality directly impacts both visual and operational performance. However, understanding mobile phone screens r...[Details]
As in-vehicle audio and video entertainment features become increasingly diverse, the demand for digital transmission of audio and video information is urgent. Traditional protocols such as IEEE 13...[Details]
According to reports from Xinhua News Agency, Tianjin University official website and other media, Chinese researchers have recently broken through the bottleneck of energy density and application ...[Details]
Since the beginning of summer, high temperatures have continued to intensify, and the national electricity load has frequently broken records. The latest data from the National Energy Administratio...[Details]
When Innovation officially announced the O sweeper recently, 13,000 users flocked to the JD flagship store to make reservations within 24 hours, confirming the market's expectation for the cross-...[Details]
The VR industry is rapidly evolving, and it seems only a matter of time before VR devices reach mass production. Of course, in its early stages, VR will primarily appear as high-end gaming devices....[Details]
This article uses a heavy-duty off-road vehicle as an example to design a gateway and body control software based on a domain controller (DC). The article also examines the feasibility of u...[Details]
As the core component of electric vehicles, power batteries determine factors such as the vehicle's range. With the increase in the number of electric vehicles, more and more people are choosing el...[Details]
The battery in an electric car is related to the vehicle's performance. As one of the core components of the vehicle, the battery cell has become an important reference for evaluating the quality o...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
