The Medallion 2100 Optical A/B Switch is a high-performance solution for network
protection and optical redundancy. Packaged in convenient 1 RU housing, this line of
optical switches provides an automatic or manual fiber switching function to protect the
network from inadvertent service outages due to up-stream optical signal degradation.
Each fiber’s optical signal power level is continuously monitored, as is an adjustable
optical trip threshold for each channel. If the primary fiber’s optical signal power level
falls below the desired optical trip threshold, the unit automatically switches to the
secondary fiber, thus eliminating the need for intervention of a system operator. The
Medallion 2100 is capable of manual switching or can be switched remotely via SNMP
or via a WEB browser adding optical protection to many system applications.
The Medallion 2100 series is designed as a low power, cost-effective, high-
performance switching solution for applications that demand reliable and rapid
response to changing network conditions.
Features
Automatic, Manual and Remote
Switching
Up to 4 Independent Switches
Auto-Switching Time Less than 10 ms
SNMPv2 Control Interface
Web Server
Front Panel LED Indicators
1 RU Rack-Mount Enclosure with Choice
of Dual Hot Swappable AC or DC
Redundant Power Supplies
Example Redundant Path Configuration for CATV Broadcast
Medallion 6000
RF In
CATV Tx (Main)
MAIN
Medallion 2100
Optical Switch
BACKUP
Medallion 7100/7200
EDFA
…
To WDM & PONs
RF In
Medallion 6000
CATV Tx (Backup)
Optical Characteristics
Property
Operating Wavelength
Insertion Loss
Return Loss
Polarization Dependent Loss
Repeatability
Cross Talk
Input Optical Power
Switching Time
Durability
Min.
1260
-
-
-
-
-
-
-
-
Typ.
≤
1.0
≥
50
≤
0.05
+/-0.02
≥
55
-
≤
10
≥
10
7
Max.
1620
1.5
-
0.1
+/-0.03
-
27
25
-
Units
nm
dB
dB
dB
dB
dB
dBm
ms
Cycles
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 2100 Optical A/B Switch
DATASHEET | JUNE 2015
FIBER OPTICS
General and Mechanical Specifications
Property
Switching Threshold
Switching Mode
Optical Connector
Monitoring Interfaces
Operating Temperature
Storage Temperature
Power Consumption
Supply Range (VAC)
(VDC)
Dimensions
Individual Switches per Rack Unit
Requirement
20 dB dynamic range – see ordering info
Auto, Manual, Remote
SC/APC
100 Base-T Ethernet
Rear Panel RS-232 interface
Front Panel Indicators
0°C to 50°C
-25°C to 65°C
15 W
85 to 240 VAC, 50/60 Hz
36 - 72 VDC
430 mm x 300 mm x 44 mm
Up to 4
EN50083-2-2006
EN 55013
EN 61000-3-2
EN 61000-4-6
EN 61000-4-3
EN 61000-4-2
EN 61000-4-4
EN 61000-3-3
FCC Part 15 (Subpart B, Class A), 107(b), 109(b)
IEC 60950-1/A1:2009
GR-2853-CORE
GR-2853-CORE
0% to 95%
Comments
Settable within range
Other styles available (see ordering information)
SNMPv2, WEB Graphical User Interface
Local Craft Interface
LED and Vacuum Fluorescent Display
Maximum
Agency Listings, EMI
Agency Listing, Safety
Transportation Vibration
Transportation Shock
Relative Humidity (non-condensing)
European Union “RoHS 2 Directive” Compliance
All homogenous materials contained in the product contain less than the maximum concentration levels for lead, mercury,
cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers permitted under the European
Union Directive 2011/65/EC (the “RoHS 2 Directive”)
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 2100 Optical A/B Switch
DATASHEET | JUNE 2015
FIBER OPTICS
Outline Drawing
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 2100 Optical A/B Switch
DATASHEET | JUNE 2015
FIBER OPTICS
Model Number Information (note 1)
2100 –
Logo &
Customer
Specific
0-EMCORE
logo
1-no
logo
Operating
Wavelength
0
- 1260 nm
to 1620 nm
–
Switch
Configuration
12 -
1 out, 2 in
13 -
1 out, 3 in
14 -
1 out, 4 in
1X -
1 out, X in
Switch
Quantity
01
– 1 switch
02
– 2
switches
03
– 3
switches
04
– 4
switches
0X
– X
switches
–
Optics
1-
SC/APC
2-
FC/APC
3-
E2000
Optical
Connection
1-
Front Mount
2-
Rear Mount
1
Switching
Threshold Range
1
–
(-20 dBm, +20 dBm)
Reserved
0
Power Supply
1 -
AC primary,
no secondary
2 -
DC primary,
no secondary
3 -
AC primary,
AC secondary
4 -
AC primary,
DC secondary
5 -
DC primary,
DC secondary
Note 1: Not all configurations are available - contact factory
Example: 2100-10-1204-11103 No logo, 1550 nm, 1 x 2 switch, 4 switches, SC/APC connectors, front mount connectors, -20
dBm to +20 dBm range, AC power supply primary, AC power supply secondary
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
This application note describes the design goals for the GPS LNA application, as well as the PCB materials and 0402 chip SMT passive components used. The designed LNA is unconditionally stable from 5M...
1. BSD TCP / IP protocol stackThe BSD stack has historically been the starting point for other commercial stacks. Most professional TCP/IP stacks ( such as the TCP/IP stack embedded in VxWorks ) are d...
I only learned about MSP430 with FRAM after attending TI and Arrow's MCU Day last time. I used to use MSP430f149 and didn't know FRAM at all. After looking up the information, I found that FRAM's perf...
I'm working on a program upgrade for MSP430F5438 recently. The host computer sends the user program via Bluetooth, and the microcontroller receives the data through a boot program and writes it to a f...
Quick Introduction to LM3S8962 Microprocessor
Since leaving the assembly era, the way people learn microcontrollers has changed significantly. In the past, it was necessary to understand the address c...
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Automotive Electronics
京公网安备 11010802033920号
EEWORLD
