integrated high gain photo detector. The output of the
detector IC is an open collector Schottky-clamped
transistor. The internal shield provides a guaranteed
common mode transient immunity specification of 15
kV/µs.
This unique design provides maximum AC and DC
circuit isolation while achieving L V T T L / L V C M O S
compatibility. The optocoupler AC and DC operational
parameters are guaranteed from –40˚C to +85˚C
allowing trouble-free system performance.
Applications
• Isolated line receiver
• Computer-peripheral interfaces
• Microprocessor system interfaces
• Digital isolation for A/D, D/A conversion
• Switching power supply
• Instrument input/output isolation
• Ground loop elimination
• Pulse transformer replacement
• Fieldbus
Features
• Package clearance/creepage at 8 mm
• Low power consumption
• 15 kV/µs minimum Common Mode Rejection (CMR) at
V
CM
= 50 V
• High speed: 15 MBd typical
• LVTTL/LVCMOS compatible
• Low input current capability: 5 mA
• Guaranteed AC and DC performance over temperature:
–40˚C to +85˚C
• Available in 6-pin stretched SO-6 and 8 pin stretched
SO-8
• Safety approvals: UL, CSA, IEC/EN/DIN EN 60747-5-2 –
in process
Functional Diagram
ACPL-W60L
ANODE
1
2
CATHODE
3
6
5
4
V
CC
V
O
CATHODE
2
SHIELD
ACPL-K63L
ANODE
1
CATHODE
1
1
2
3
4
SHIELD
*
8
7
6
5
V
CC
V
O1
V
O2
GND
GND
ANODE
2
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
OUTPUT
L
H
*Advanced Information
A 0.1
µF
bypass capacitor must be
connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent
damage and/or degradation which may be induced by ESD.
Schematic Diagrams
I
F
1+
ACPL-W60L
I
CC
6
I
O
5
V
CC
ACPL-K63L
I
CC
1
V
O
I
F1
8
I
O1
7
V
CC
V
O1
+
V
F1
V
F
–
3
SHIELD
4
GND
–
2
SHIELD
3
–
I
O2
6
V
O2
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5).
V
F2
+
4
I
F2
SHIELD
5
GND
These optocouplers are suitable
for high speed logic interfacing,
input/output buffering, as line
receivers in environments that
conventional line receivers
cannot tolerate and are
recommended for use in
extremely high ground or induced
noise environments.
These optocouplers are available
in stretched SO-6 and SO-8
package. The part numbers are as
follows:
Package
Stretched SO-6
Stretched SO-8
Ordering Information
Specify Part Number followed by Option Number (if desired).
Example:
ACPL-W60L -XXXX
020 = UL5000 Vrms/minute Option
060 = IEC/EN/DIN EN 60747-5-2
500 = Tape and Reel Packaging Option
XXXE = Lead Free Option
Example:
ACPL-K63L -XXXX*
020 = UL5000 Vrms/minute Option – pending
qualification
060 = IEC/EN/DIN EN 60747-5-2
500 = Tape and Reel Packaging Option
XXXE = Lead Free Option
Option data sheets available. Contact Avago sales representative or
authorized distributor for information.
ACPL-W60L
ACPL-K63L
2
Package Outline Drawings
ACPL-W60L Stretched SO-6 Package
LAND PATTERN RECOMMENDATION
12.65 (0.498)
1.27 (0.050) BSG
0.381
±
0.127
(0.015
±
0.005)
1
2
3
6
5
4
+0.254
4.580 0
+0.010
0.180
-0.000
0.76 (0.030)
(
)
(
0.45 (0.018)
7°
+0.127
6.807 0
+0.005
0.268
-0.000
1.91 (0.075)
)
1.590
±
0.127
(0.063
±
0.005)
7°
45°
3.180
±
0.127
(0.125
±
0.005)
0.20
±
0.10
(0.008
±
0.004)
0.750
±
0.250
(0.0295
±
0.010)
11.50
±
0.250
(0.453
±
0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.1 mm (0.004 INCHES).
ACPL-K63L Stretched SO-8 Package
LAND PATTERN RECOMMENDATION
12.650 (0.5)
1.270 (0.050) BSG
0.381
±
0.13
(0.015
±
0.005)
1
2
3
4
8
7
6
5
+0.25
5.850 0
+0.010
0.230
-0.000
(
)
0.450 (0.018)
7°
1.590
±
0.127
(0.063
±
0.005)
45°
3.180
±
0.127
(0.125
±
0.005)
1.905 (0.1)
7°
0.200
±
0.100
(0.008
±
0.004)
0.750
±
0.250
(0.0295
±
0.010)
6.807
±
0.127
(0.268
±
0.005)
11.5
±
0.250
(0.453
±
0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.1 mm (0.004 INCHES).
3
Recommended Solder Reflow Thermal Profile
300
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
PEAK
TEMP.
245°C
PEAK
TEMP.
240°C
PEAK
TEMP.
230°C
2.5°C ± 0.5°C/SEC.
160°C
150°C
140°C
3°C + 1°C/–0.5°C
30
SEC.
30
SEC.
SOLDERING
TIME
200°C
TEMPERATURE (°C)
200
100
PREHEATING TIME
150°C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
0
50
100
150
200
250
TIME (SECONDS)
Note:
Use of non chlorine-activated fluxes is highly recommended.
Recommended PB-Free IR Profile
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
t
p
T
p
T
L
260 +0/-5 °C
217 °C
RAMP-UP
3 °C/SEC. MAX.
150 - 200 °C
TEMPERATURE
T
smax
T
smin
RAMP-DOWN
6 °C/SEC. MAX.
t
s
PREHEAT
60 to 180 SEC.
25
t 25 °C to PEAK
t
L
60 to 150 SEC.
TIME
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
T
smax
= 200 °C, T
smin
= 150 °C
Note:
Use of non chlorine-activated fluxes is highly recommended.
Regulatory Information
The ACPL-W60L//K63L have
been approved by the following
organizations:
UL - Pending
CSA - Pending
IEC/EN/DIN EN 60747-5-2 - Pending
Approval under CSA Component
Acceptance Notice #5, File CA
88324.
Approval under UL 1577,
Component Recognition
Program, File E55361.
4
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884
Teil 2):2003-01
(Option 060 only)
Insulation and Safety Related Specifications
Stretched
SO-6 and SO-8
Value
8
8
0.08
Parameter
Minimum External Air
Gap (External Clearance)
Minimum External Tracking
(External Creepage)
Minimum Internal Plastic
Gap (Internal Clearance)
Symbol
L (101)
L (102)
Units
mm
mm
mm
Tracking Resistance
(Comparative Tracking
Index)
Isolation Group
CTI
175
Volts
Conditions
Measured from input terminals to output
terminals, shortest distance through air.
Measured from input terminals to output
terminals, shortest distance path along body.
Through insulation distance, conductor to
conductor, usually the direct distance
between the photoemitter and photodetector
inside the optocoupler cavity.
DIN IEC 112/VDE 0303 Part 1
IIIa
Material Group (DIN VDE 0110, 1/89, Table 1)
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
Description
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage
≤
150 V rms
for rated mains voltage
≤
300 V rms
for rated mains voltage
≤
600 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
V
IORM
x 1.875 = V
PR
, 100% Production Test
with t
m
= 1 sec, Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
V
IORM
x 1.5 = V
PR
, Type and Sample Test,
t
m
= 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, t
ini
= 10 sec)
Safety Limiting Values
Case Temperature
Input Current
Output Power
Insulation Resistance at T
S
, V
IO
= 500 V
Symbol
Stretched S0-6 & SO-8 Value
I-IV
I-III
I-II
55/100/21
2
630
1181
Units
V
IORM
V
PR
V
peak
V
peak
V
PR
V
IOTM
945
6000
V
peak
V
peak
T
S
I
S,INPUT
P
S,OUTPUT
R
S
175
230
600
˚C
mA
mW
≥
10
9
Ω
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed
description.
Note:
Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Project_zero of cc2640r2f adds pwm output to the peripheral circuit to drive the small motor function: cc2640r2f outputs 4 controllable PWM, 2 signals can drive a small motor forward and reverse signa...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:57[/i]Common electronic component detection methods and experience (Part 1) Component detection is a basic skill for home appliance mai...
[i=s]This post was last edited by Bai Ding on 2016-2-7 17:42[/i] Reposted from [url=http://www.21ic.com/mcucourse/201601/661616.htm]http://www.21ic.com/mcucourse/201601/661616.htm[/url] Over the past ...
I used to use CCS3.3, because the software was too prone to blue screens and crashes, and using a virtual machine seriously affected the speed of the emulator. So I switched to CCS5.2.The ECLIPS archi...
Where should the mpu6050 be placed? What are the differences between the results measured in different places? The purpose of solving the above problems is to obtain a more accurate pendulum deflectio...
I use C++ to create an array, char mmsContent[65535]; memset(mmsContent, 0, sizeof(mmsContent)); but the program will exit when it reaches the array declaration. It also doesn't work to create it in t...
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
Among the uses of electrical energy, lighting accounts for a considerable proportion. Compared with the earlier ordinary incandescent lamps, the fluorescent lamps and energy-saving lamps we commonl...[Details]
Movpower is a portable power bank. It can charge most mobile phones and digital products, such as digital cameras, PDAs, and mobile phones such as Apple, iPod, Blackberry, Motorola, Samsung, Nokia,...[Details]
1 Introduction to the overall system solution
The hardware part is mainly used to amplify the sound. When the sound is loud enough, the signal can be introduced into the microcontroller for de...[Details]
introduction
Sudan's Muglad Oilfield is a large oilfield jointly invested, developed and constructed by a four-party consortium of China, Malaysia, Canada and Sudan. It consists of 8 satellite...[Details]
Introduction
Temperature and humidity control are widely used in people's production and life. People use thermometers and hygrometers to collect temperature and humidity, and control temperatu...[Details]
The rotor of the brushless DC motor used in electric bicycles is composed of 30 to 40 pieces of NdFeB magnets. Since the surface magnetic field strength of NdFeB magnets exceeds 500mT, the position se...[Details]
In recent years, the development of automotive batteries has become a focus of attention. Compared with other rechargeable batteries, lithium-ion batteries have the advantages of high specific ene...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
