EEWORLDEEWORLDEEWORLD

Part Number

Search

2556-13-27-17

Description
Board Connector, 27 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Receptacle
CategoryThe connector    The connector   
File Size133KB,2 Pages
ManufacturerConexcon Group
Environmental Compliance
Download Datasheet Parametric View All

2556-13-27-17 Overview

Board Connector, 27 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Receptacle

2556-13-27-17 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerConexcon Group
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.1 inch
subject depth0.1 inch
body length2.7 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage600VAC V
Durability50 Cycles
Insulation resistance1000000000 Ω
insulator materialTHERMOPLASTIC
Manufacturer's serial number2556
Plug contact pitch0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
Plating thicknessFLASH inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.118 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts27
SINGLE ROW VERTICAL PIN HEADER
2556 SERIES.
2.54 mm (0.100”) pitch.
General Features
Electrical Features
Available in 2 through 40 circuits
Mates with sockets 2.54 mm pitch 2101, 2550, 2595, 2596,
2553, 2554,2247, 2551, 2552, 2577, 2102, 2106, 2452 series
0,64 mm. square pin with different plating
Different pin length available
Consult Sales Office
Voltage rating: < 250V
Current rating: < 3 A
Contact resistance: < 20 mΩ
Dielectric withstanding voltage: 600 V AC/minute
Insulation resistance: >1000 MΩ
Capacitance: < 2 pF at 1 KHz
Materials
Mechanical Features
Insulator: High temperature thermoplastic UL 94 V-0
Contact: brass
Operating temperature: -40ºC to +105ºC
RoHS compliant
Pin retention force to insulator: > 0,50 Kgf
Durability: 50 cycles
Dimensional Information
0.64
.025
H
Ordering Information:
3.00
.118
2.54
.100
A
B
2556 -
1
T-
2
XX-
3
C
4
2.54
.100
1. Connector Series
2. (T) Contact Plating
2.54
.100
T =
2.
Tin plated
T =
3.
Gold flash over nickel
Recommended Finish
2.54±0.05
.100±.002
1.20±0.10
.047±.004
T =
5.
15µ” gold over nickel
T =
6.
30µ” gold over nickel
T =
13.
Sel. gold flash over nickel overall
T =
15.
15µ" sel. gold over nickel overall
T =
16.
30µ" sel. gold over nickel overall
RECOMMENDED HOLE PATTERN
3. (XX) Number of circuits
100
Available in 2 through 40 circuits
5. (C) Pin Dimensions
Opcional:
Plastic base without pins
P/N:
2556-00XX
(XX= Nº circuits)
The dimension H are optional
(Check te dimmensions table and consult Sales Office)
Dimensions:
(In mm.)
A
= 2.54 x (XX*-1)
B
= 2.54 x (XX*)
* XX
(Number of circuits)
E-XX
FULL LINE CATALOGUE
Entering the world of microcontrollers
Entering the world of microcontrollers    Nowadays, everyone is familiar with computers. From the overwhelming advertisements for computer classes to the notice that computer knowledge is required for...
zdr Test/Measurement
Request information
Make a remote control car, need guidance, use a single chip microcomputer...
方炯锟 51mcu
Novice asks for advice: 6410 serial port driver
I'm looking at the 6410 serial port driver recently and I'm confused. I hope you guys can share some experience. How should I look at this aspect? How much should I look at? How to deal with the drive...
fgfgfg Embedded System
EEWORLD University Hall----Live Replay: Introduction to ST MEMS Sensor Development Kit, Understanding Sensors with Embedded "Finite State Machine and Machine Learning Core"
Live replay: Introduction to ST MEMS sensor development kit, understanding sensors with embedded "finite state machine and machine learning core" : https://training.eeworld.com.cn/course/5550...
hi5 Analog electronics
How does EXTI determine whether the interrupt is rising or falling?
The EXTI port line is set to interrupt on rising edge and falling edge. After the interrupt is entered, how to determine whether it is caused by the rising edge or the falling edge? The high and low l...
system110 stm32/stm8
AM335x about eeprom using i2c1 interface
00: [ 2558.385070] omap_i2c omap_i2c.2: timeout waiting for bus ready root@am335x-evm:~# i2cdetect -r 2 WARNING! This program can confuse your I2C bus, cause data loss and worse! I will probe file /de...
爱JustdoIT DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 647  628  2141  69  788  14  13  44  2  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号