EEWORLDEEWORLDEEWORLD

Part Number

Search

54112-110-62-1100

Description
Board Connector, 62 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size67KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54112-110-62-1100 Overview

Board Connector, 62 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54112-110-62-1100 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.433 inch
body length3.1 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54112
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts62
PDM: Rev:G
STATUS:
Released
Printed: Feb 20, 2009
.
How to set unused pins in Quartus II
Dear experts, how should I set the unused pins in Quartus II? The default setting in the software is As output driving ground, but the Internet says that this setting will cause the chip to heat up. G...
沉默珏殇 FPGA/CPLD
Xunwei-i.MX6 development board manual update-non-device tree uboot-modify default environment variables
This document mainly introduces how to modify the default boot parameters of non-device tree uboot. After the iTOP-iMX6 development board is burned, the default is the system parameters and screen par...
遥寄山川 ARM Technology
Problems encountered when using CH375 to communicate with PC in device mode.
I used DEBUG372.EXE (downloaded debugging tool) on the host computer. I uploaded several numbers to endpoint 1 and endpoint 2, and they were normal. When I downloaded to endpoint 2, the "number of dat...
ykfall Embedded System
How to solve the signal fluctuation from the sensor?
The signal from the sensor is very weak, and the circuit behind it has been amplified and filtered. When the detection quantity remains unchanged, the amplified signal has certain fluctuations. Lookin...
sfcsdc Analog electronics
AD Software
Can Altium Design software simulate? That is, the components have actual input and output, rather than just drawing schematics and then onto the PCB board....
如此美好 PCB Design
Problems in using LMT01 temperature measurement
I have recently been using the temperature measuring element LMT01 produced by TI. I chose your TI product based on its own measurement range and low power consumption. According to the official data ...
zb495203317 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2449  370  1972  2900  97  50  8  40  59  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号