EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCM-215-S-16-GT-168

Description
Board Connector, 15 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Receptacle
CategoryThe connector    The connector   
File Size174KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCM-215-S-16-GT-168 Overview

Board Connector, 15 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Receptacle

BSTCM-215-S-16-GT-168 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerMajor League Electronics
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresHIGH TEMPERATURE
body width0.079 inch
body length1.187 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial numberBSTCM
Plug contact pitch0.079 inch
Installation methodSTRAIGHT
Number of connectorsONE
PCB row number2
Number of rows loaded1
Maximum operating temperature250 °C
Minimum operating temperature-65 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.286 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch3.9878 mm
Total number of contacts15
Why does the output voltage of an op amp need to be offset? Analysis of the principle of differential circuit
The differential operational amplifier circuit effectively suppresses the common-mode signal and only amplifies the differential signal, so it is widely used.Circuit Configuration of Differential Circ...
infinigo Integrated technical exchanges
[Mill MYC-J1028X development board trial] Use Node-RED to transform the MYC-J1028X development board into an industrial control gateway
[i=s]This post was last edited by HonestQiao on 2022-10-2 10:59[/i]This article is long and involves many knowledge points. You need to read it patiently. The following is the directory of specific co...
HonestQiao NXP MCU
How to transfer Q, I, and M registers to V register in PLC program?
[size=3]Please give me some advice on how to transfer Q, I, M registers to V register in PLC program[/size]...
eeleader Industrial Control Electronics
CCS3.3 Chinese Learning Manual
I have uploaded two Chinese learning manuals for CCS3.3, I hope they will be helpful to everyone!...
kooking DSP and ARM Processors
Programs written in EVC cannot open the GPIO driver when operated under wince5.0
I used evc to write a gpio output program, but when I opened the driver with wince system, it showed that the gpio driver failed to be opened. I don't know why. I used the s3c2440 experimental board o...
gaoli.85 Embedded System
The terminal cannot collect temperature and humidity information after waking up from sleep
As the title says, when I make the node not sleep, that is, when I do not add the POWER_SAVING compilation option, the node can collect temperature and humidity information normally. However, when I a...
浩海狂澜 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2348  2533  235  2278  2775  48  52  5  46  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号