EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-819-59-0800LF

Description
Board Connector, 118 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54122-819-59-0800LF Overview

Board Connector, 118 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54122-819-59-0800LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.315 inch
body length5.9 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts118
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
Soft keyboard problem
I wrote a soft keyboard program, which simulates sending soft keyboard messages through keybd_event. However, the edit box cannot receive the soft keyboard input, but the dialog box where the edit box...
ryzhou Embedded System
How to create a visual effect of TCPMP playback
Can it be achieved by calling the MediaPlayer Visualization module mpvis.dll, or other methods?...
kingdomabc Embedded System
Power measurement circuit for telecommunication equipment (reprinted)
This article discusses how to monitor the input voltage and current of telecom equipment with two independent inputs (-48V (A) and -48V (B)). The voltage range of each independent input is not narrowe...
电子元件 Test/Measurement
Differences between 74 series circuits and CMOS series circuits
Not long ago, I needed to design a timing circuit with a delay of 5 seconds. The design idea was finalized, but there was a problem during the experiment. The following figure is the circuit that need...
clark MCU
Selection and Differences of Isolated Oscilloscopes and Differential Probes
Sometimes it is dangerous to use an oscilloscope to measure a circuit system with a potential difference. This danger may come from a short circuit inside the device or from the potential itself. As t...
Micsig麦科信 Test/Measurement
How to write the driver?
I want to write a signal receiver driver. For example, if I put many signal receivers in the examination room, I can observe the status of all signal receivers on the computer after writing a driver. ...
amork2007 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2923  1800  2228  1604  994  59  37  45  33  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号