3000-610-2004 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 3000-610-2004

3000-610-2004: DescriptionBoard Connector, 10 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size173KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

3000-610-2004 Overview

Board Connector, 10 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3000-610-2004 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	WITH LOCKING RAMP
subject depth	0.45 inch
body length	1.554 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	SN ON CU
Contact completed and terminated	TIN OVER COPPER
Contact point gender	MALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1500VAC V
maximum insertion force	8.896 N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	NYLON
Manufacturer's serial number	3000
Plug contact pitch	0.156 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Plating thickness	200u inch
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.218 inch
Terminal pitch	3.9624 mm
Termination type	SOLDER
Total number of contacts	10
Evacuation force-minimum value	.556 N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Right Angle Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

POLARIZING KEY &

LOCKING RAMP

LEG

HOOK

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

Single tube constant current charger circuit diagram

TDA1701 power amplifier circuit diagram

HFC5230 "Please note there is a fault" language integrated circuit

Low frequency pulse generator circuit diagram

Wireless remote control/touch dimming circuit (RCM1A/RCM1B)

Computer motherboard circuit diagram 810 3_10

Circuit Schematic Analysis Method: [i=s]This post was last edited by CokezzZ on 2021-7-13 08:39[/i]The concept of electronic circuit schematics A conductive loop consisting of metal wires and electrical and electronic components is cal...; 可乐zzZ Energy Infrastructure?

Problems with peripheral shared registers of msp430: The datesheet of the msp430 microcontroller clearly states that the chip has I2C, SPI, and UART. The user manual makes it seem that each is a separate module, but in fact, it is not the case when used...; fish001 Microcontroller MCU

LCD interface design issues: Hey guys, I'm new to FPGA. Now I need to write an LCD soft core design based on FPGA (using EP1C6Q240C8), which is required to adapt to the mainstream LCDs with different interfaces. I hope to get som...; morninghan2 Embedded System

USB Development--DEVICE_INFO: The program is as follows: typedef struct _DEVICE_INFO { uint8_t USBbmRequestType; /* bmRequestType */ uint8_t USBbRequest; /* bRequest */ uint16_t_uint8_t USBwValues; /* wValue */ uint16_t_uint8_t US...; liuchang--- stm32/stm8

232 receiving problem,: My program can send and receive data normally, but when receiving data from the touch serial terminal, it can only receive two bytes after each reset, and the subsequent data cannot be received. My pr...; ywqaxiwang stm32/stm8

UART1 cannot send data: I want to send data 05 to the serial port, the function is as follows, but it can't be displayed on the serial port. What is the problem?#include "stm32f10x.h"GPIO_InitTypeDef GPIO_InitStructure;USART...; vipczx stm32/stm8

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components