BHR26HSGAGY datasheet, PDF - EEWORLD Datasheet

BHR26HSGAGY: DescriptionBoard Connector, 26 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Gray Insulator, Receptacle; CategoryThe connector The connector; File Size355KB，2 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

BHR26HSGAGY Overview

Board Connector, 26 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Gray Insulator, Receptacle

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
body width	0.36 inch
body length	1.605 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU
Contact completed and terminated	GOLD
Contact point gender	MALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	20 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1000VAC V
Durability	750 Cycles
maximum insertion force	2.224 N
Insulation resistance	5000000000 Ω
Insulator color	GRAY
insulator material	GLASS FILLED POLYBUTYLENE TEREPHTHALATE
Manufacturer's serial number	BHR
Plug contact pitch	0.1 inch
Match contact row spacing	0.1 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	125 °C
Minimum operating temperature	-65 °C
PCB contact pattern	RECTANGULAR
PCB contact row spacing	2.54 mm
Plating thickness	5u inch
polarization key	CENTER
Rated current (signal)	3 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.145 inch
Terminal pitch	2.54 mm
Termination type	SOLDER
Total number of contacts	26
Evacuation force-minimum value	.417 N

Big Brother, please help: There is a USB detection. When the USB is detected, the red light in RGB will be displayed. When the key is pressed for the first time, it will light up white. There are five gears corresponding to fi...; 陈其海 ADI Reference Circuit

PCB automatic routing failed: When I used the board wizard, I set the following rules to run two lines between two pads. However, after I finished the layout and routed, I found that my board components were a bit dense, and the t...; 面纱如雾 PCB Design

Problems with adding vias to PCB boards: As the title says, for example, for a two-layer PCB After copper is applied to both the top GND and the bottom GND Why do we need to place several vias on the GND copper between the two layers? (After...; shaorc PCB Design

430 driver sx1278, the program has been debugged, shared source code [: [b]430 driver sx1278, the program has been debugged, shared source code[/b][color=rgb(153, 153, 153) !important][/color] [b][/b]...; Jacktang Microcontroller MCU

Ask a Question!: There are 10 channels of signals to be tested that need to be output from the serial port to the PC. I connect them to the P0 and P1 ports through 2 latches, and select the data of the P0 and P1 ports...; opper Embedded System

The DHT11 code does not respond at all. Is it because I understand it too simply? Please take a look.: [code]#define DHT_H_1 PORTD|=(120us wait 25us for DHT to respond if(PIND7==0)//Check pin7 status. DHT pulls PIN7 low to respond { while(PIND7==0)//Wait for DHT to pull PIN7 low 80us while(PIND7==1)//W...; zqdl8 Microchip MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components