ATC GENERAL PURPOSE CAPACITORS: NPO (COG) DIELECTRIC
ELECTRICAL CHARACTERISTICS
CAPACITANCE RANGE:
0.5 pF to 0.10 µF.
TEMPERATURE CHARACTERISTIC:
0 ± 30ppm/°C.
L
W
OPERATING TEMPERATURE RANGE:
-55°C to +125°C.
DISSIPATION FACTOR:
0.1% (max.) @ + 25°C,
@1 MHz
≤
1000 pF; @1 KHz >1000 pF
INSULATION RESISTANCE
@ + 25°C and rated Vdc:
100,000 megohms (min.) or 1000 ohm-farads (min.),
whichever is less.
DIELECTRIC WITHSTANDING VOLTAGE:
250% of rated voltage for 5 ± 1 seconds, 50 milliamps (max.).
Unless otherwise specified all test data is at + 25°C.
T (MAX.)
MB
Temperature Coefficient
Aging Rate
Voltage Coefficient of Capacitance
Temperature (Celsius)
Impedance vs. Frequency
Dissipation Factor vs. Frequency
Minimum IR vs. Temperature
Temperature (Celsius)
Sales of ATC products are subject to the terms and conditions contained in American Technical Ceramics Corp. Terms and Conditions of Sale(ATC document #001-992 Rev. A 10/03). Copies of
these terms and conditions will be provided upon request. They may also be viewed on ATC's website at www.atceramics.com/productfinder/default.asp. Click on the link for Terms and
Conditions of Sale.
ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which
may result from its use. ATC reserves the right to revise the content or modify its product without prior notice.
[i=s]This post was last edited by dcexpert on 2015-11-10 23:37[/i] Collect official resources of various development boards for easy search. (This post will be continuously updated, and everyone is we...
In Windows Mobile 6.0 or 6.1, in "Settings" "Connections" -> "WiFi prefs" in the "enroll" column, I don't know how to obtain the certificate?? There is no detailed solution and help, thank you! !...
It was working fine last night, but this morning I can't download the program. The connections are all correct and I have replaced the microcontroller. Has anyone encountered this situation before?...
I made several circuit boards with STM32F103C6, and used JLINK+KEIL MDK as the simulation tool. I couldn't simulate the first one after welding, but it worked after a while, and the software test pass...
During the development of the challenge, I encountered a problem. If the external IO is not processed when BlueNRG-1 enters sleep mode, the current will fluctuate unstably. When it is high, it can rea...
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Security PPP is a new model of urban video surveillance projects: 1) The government and social capital establish a project company in a certain proportion; 2) The project company participates in the ...[Details]
ZTE was punished, and Hou Weigui, who had already retired, had to come out of retirement again and run around to mediate. Let's follow the embedded editor to learn about the relevant content.
...[Details]
This program uses the eight-channel ADC single acquisition mode. According to the configuration, ADC12SC will automatically reset after the conversion is completed in the single mode, so it is necess...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
1. Common knowledge about DMA. 1. Function: to achieve high-speed data transmission between chips. That is, it can achieve data transmission without occupying the CPU. 2. Mode: There are three tran...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
Use common anode digital tube and independent keyboard to connect P1 and P2 ports of single chip to realize answering machine The procedure is as follows: #include reg52.h void delay(unsigned char n)...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
Assume that both the augend NA and the addend NB are three-byte compressed BCD codes, which are stored in the internal RAM units 20H~22H and 30H~32H, respectively, with the low digit first and the hi...[Details]
Title: Use two dynamic digital tubes to display from 0 to 60, output from the P1 port of 89C51, without adding a decoder, and directly connect the digital tubes. Note that they are dynamic digital tu...[Details]
Bitcoin
It has been a roller coaster ride, with regulatory winds tightening. Some retail investors and small miners have left, while large miners have returned and some have moved overseas. L...[Details]
China Energy Storage Network News:
The Global Energy Internet Seminar, jointly organized by the Global Energy Internet Development Cooperation Organization and the Royal Academy of Engineerin...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
