EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
3014bfb
2
For more information
www.linear.com/LT3014B
LT3014B
ORDER INFORMATION
LEAD FREE FINISH
LT3014BES5#PBF
LT3014BIS5#PBF
LT3014BMPS5#PBF
LT3014BHVES5#PBF
LT3014BHVIS5#PBF
LT3014BEDD#PBF
LT3014BIDD#PBF
LT3014BHVEDD#PBF
LT3014BHVIDD#PBF
LEAD BASED FINISH
LT3014BES5
LT3014BIS5
LT3014BMPS5
LT3014BHVES5
LT3014BHVIS5
LT3014BEDD
LT3014BIDD
LT3014BHVEDD
LT3014BHVIDD
TAPE AND REEL
LT3014BES5#TRPBF
LT3014BIS5#TRPBF
LT3014BMPS5#TRPBF
LT3014BHVES5#TRPBF
LT3014BHVIS5#TRPBF
LT3014BEDD#TRPBF
LT3014BIDD#TRPBF
LT3014BHVEDD#TRPBF
LT3014BHVIDD#TRPBF
TAPE AND REEL
LT3014BES5#TR
LT3014BIS5#TR
LT3014BMPS5#TR
LT3014BHVES5#TR
LT3014BHVIS5#TR
LT3014BEDD#TR
LT3014BIDD#TR
LT3014BHVEDD#TR
LT3014BHVIDD#TR
PART MARKING*
LTCHK
LTCHK
LTCHK
LTCHN
LTCHN
LCHM
LCHM
LCHP
LCHP
PART MARKING*
LTCHK
LTCHK
LTCHK
LTCHN
LTCHN
LCHM
LCHM
LCHP
LCHP
PACKAGE DESCRIPTION
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
PACKAGE DESCRIPTION
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
5-Lead Plastic SOT-23
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
This product is only offered in trays. For more information go to: http://www.linear.com/packaging/
3014bfb
For more information
www.linear.com/LT3014B
3
LT3014B
ELECTRICAL CHARACTERISTICS
SYMBOL
Minimum Input Voltage
ADJ Pin Voltage
(Notes 2, 3)
Line Regulation
Load Regulation
Dropout Voltage
V
IN
= V
OUT(NOMINAL)
(Notes 4, 5)
CONDITIONS
I
LOAD
= 20mA
V
IN
= 3.3V, I
LOAD
= 100µA
3.3V < V
IN
< 80V, 100µA < I
LOAD
< 20mA
DV
IN
= 3.3V to 80V, I
LOAD
= 100µA (Note 2)
V
IN
= 3.3V,
DI
LOAD
= 100µA to 20mA (Note 2)
V
IN
= 3.3V,
DI
LOAD
= 100µA to 20mA
I
LOAD
= 100µA
I
LOAD
= 100µA
I
LOAD
= 1mA
I
LOAD
= 1mA
I
LOAD
= 10mA
I
LOAD
= 10mA
I
LOAD
= 20mA
I
LOAD
= 20mA
GND Pin Current
V
IN
= V
OUT(NOMINAL)
(Notes 4, 6)
I
LOAD
= 0mA
I
LOAD
= 100µA
I
LOAD
= 1mA
I
LOAD
= 10mA
I
LOAD
= 20mA
C
OUT
= 0.47µF, I
LOAD
= 20mA, BW = 10Hz to 100kHz
(Note 7)
V
IN
= 7V (Avg), V
RIPPLE
= 0.5V
P-P
, f
RIPPLE
= 120Hz, I
LOAD
= 20mA
V
IN
= 7V, V
OUT
= 0V
V
IN
= 3.3V,
DV
OUT
= –0.1V (Note 2)
V
IN
= –80V, V
OUT
= 0V
V
OUT
= 1.22V, V
IN
< 1.22V (Note 2)
l
l
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C.
MIN
1.200
1.180
TYP
3
1.220
1.220
1
13
120
l
MAX
3.3
1.240
1.260
10
25
40
180
250
270
360
350
450
410
570
20
30
100
450
1000
10
UNITS
V
V
V
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
µA
µA
µA
µA
µA
µV
RMS
nA
dB
mA
mA
200
l
300
l
350
l
l
l
l
l
l
7
12
40
250
650
115
4
60
25
70
70
Output Voltage Noise
ADJ Pin Bias Current
Ripple Rejection
Current Limit
Input Reverse Leakage Current
Reverse Output Current (Note 8)
6
2
4
mA
µA
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT3014B is tested and specified for these conditions with the
ADJ pin connected to the OUT pin.
Note 3:
Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4:
To satisfy requirements for minimum input voltage, the LT3014B
is tested and specified for these conditions with an external resistor
divider (249k bottom, 392k top) for an output voltage of 3.3V. The external
resistor divider adds a 5µA DC load on the output.
Note 5:
Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage is equal to (V
IN
– V
DROPOUT
).
Note 6:
GND pin current is tested with V
IN
= V
OUT
(nominal) and a current
source load. This means the device is tested while operating in its dropout
region. This is the worst-case GND pin current. The GND pin current
decreases slightly at higher input voltages.
Note 7:
ADJ pin bias current flows into the ADJ pin.
Note 8:
Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out of the GND pin.
Note 9:
The LT3014B is tested and specified under pulse load conditions
such that T
J
@
T
A
. The LT3014BE is 100% tested at T
A
= 25°C.
Performance at –40°C to 125°C is assured by design, characterization,
and statistical process controls. The LT3014BI is guaranteed over the full
–40°C to 125°C operating junction temperature range. The LT3014BMP is
100% tested and guaranteed over the –55°C to 125°C operating junction
temperature range.
Note 10:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
The company now has two products, one is ARM7 and the other is SyncMOS sm8958A. There is also an Atmel ATF1508AS on the board. Now I am asked to take over. Where should I start? I used to do software ...
When I used stm32 before, I was deeply impressed by the serial port debugging component of Atom, so I transplanted the component to test the serial port function debugging function.The Atom component ...
I use P1.7 of P1 port as interrupt, the falling edge is valid, and P1IFG is set to 0x80 when detected,but while(P1IFG&0X80) or while((P1IN&0X80)==0) cannot be used and cannot enter the loop.I can chan...
1. Micro-transmitting power: maximum transmitting power of 17dbm (50mW). 2. Operating carrier frequency 470-490MHz, no need to apply for frequency. 3. Professional industrial-grade embedded design, sm...
BCSCTL1 = XT2OFF; I use this statement to turn off XT2CLK, but why does XT2CLK still function as clock output after BCSCTL2 = SELM_2+ DIVM_0 + SELS + DIVS_0; instead of automatically switching to DOC ...
Dual-mode inverters can operate both in conjunction with the grid and independently. These inverters can inject excess energy from renewable energy and storage devices into the grid, and withdraw p...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
The mass production process of the new generation of cockpit platform has started, and the smart cockpit market has entered a new bonus cycle of technology iteration and platform upgrade.
...[Details]
summary
There are multiple approaches to making industrial systems more intelligent, including applying artificial intelligence (AI) technology at the edge and in the cloud to sensor...[Details]
Logic analyzers are widely used tools in digital design verification and debugging. They can verify the proper functioning of digital circuits and help users identify and troubleshoot faults. They ...[Details]
When discussing autonomous driving technology, there are often two extremes: on the one hand, there's the vision of "fully autonomous driving," while on the other, there's concern about potential s...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Electric vehicles are becoming increasingly popular, with increasingly longer ranges. There are two ways to charge electric vehicles: slow charging and fast charging. Which is the most suitable? Sl...[Details]
One of the most core components of electric vehicles is the motor. The power supply provides electrical energy to the motor, which converts this electrical energy into mechanical energy, which in t...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Office (USPTO) for a patent for a door anti-collision system that may be used in future Ford vehicl...[Details]
China, August 21, 2025 – STMicroelectronics (NYSE: STM), a world-leading semiconductor company serving a wide range of electronics applications, has published its IFRS 2025 semi-annual financial re...[Details]
There are many motors that can use thyristor speed control, and they can be used in almost all industries. Various types of motors, such as fans, pumps, AC motors, DC motors, torque motors, single-...[Details]
Plug-in hybrid vehicles (PHEVs) utilize two powertrains. Their pure electric range is typically inferior to that of pure electric vehicles, often reaching less than half that. Currently, mainstream...[Details]
Consumer demand for premium listening experiences has driven rapid evolution in the wireless headphone market in recent years. Hybrid designs, which utilize two drivers per earbud to enhance sound ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
