EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB
MSE PACKAGE
12-LEAD PLASTIC MSOP
T
JMAX
= 150°C,
θ
JA
= 33°C/W,
θ
JC
= 8°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LT3045EDD#PBF
LT3045IDD#PBF
LT3045HDD#PBF
LT3045MPDD#PBF
LT3045EMSE#PBF
LT3045IMSE#PBF
LT3045HMSE#PBF
AUTOMOTIVE PRODUCTS**
LT3045EMSE#WPBF
LT3045IMSE#WPBF
LT3045HMSE#WPBF
LT3045EMSE#WTRPBF
LT3045IMSE#WTRPBF
LT3045HMSE#WTRPBF
3045
3045
3045
12-Lead Plastic MSOP
12-Lead Plastic MSOP
12-Lead Plastic MSOP
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
TAPE AND REEL
LT3045EDD#TRPBF
LT3045IDD#TRPBF
LT3045HDD#TRPBF
LT3045MPDD#TRPBF
LT3045EMSE#TRPBF
LT3045IMSE#TRPBF
LT3045HMSE#TRPBF
PART MARKING*
LGYP
LGYP
LGYP
LYGP
3045
3045
3045
PACKAGE DESCRIPTION
10-Lead (3mm
×
3mm) Plastic DFN
10-Lead (3mm
×
3mm) Plastic DFN
10-Lead (3mm
×
3mm) Plastic DFN
10-Lead (3mm
×
3mm) Plastic DFN
12-Lead Plastic MSOP
12-Lead Plastic MSOP
12-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Tape and reel specifications.
Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix.
**Versions
of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These
models are designated with a #W suffix. Only the automotive grade products shown are available for use in automotive applications. Contact your
local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for
these models.
2
Rev. C
For more information
www.analog.com
LT3045
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C.
PARAMETER
Input Voltage Range
Minimum IN Pin Voltage I
LOAD
= 500mA, V
IN
UVLO Rising
V
IN
UVLO Hysteresis
(Note 2)
Output Voltage Range
V
IN
> V
OUT
SET Pin Current (I
SET
)
Fast Start-Up Set Pin
Current
Output Offset Voltage
V
OS
(V
OUT
– V
SET
)
(Note 4)
Line Regulation: ∆I
SET
Line Regulation: ∆V
OS
Load Regulation: ∆I
SET
Load Regulation: ∆V
OS
Change in I
SET
with V
SET
Change in V
OS
with V
SET
Change in I
SET
with V
SET
Change in V
OS
with V
SET
Dropout Voltage
V
IN
= 2V, I
LOAD
= 1mA, V
OUT
= 1.3V
2V < V
IN
< 20V, 0V < V
OUT
< 15V, 1mA < I
LOAD
< 500mA (Note 3)
V
PGFB
= 289mV, V
IN
= 2.8V, V
SET
= 1.3V
V
IN
= 2V, I
LOAD
= 1mA, V
OUT
= 1.3V
2V < V
IN
< 20V, 0V < V
OUT
< 15V, 1mA < I
LOAD
< 500mA (Note 3)
V
IN
= 2V to 20V, I
LOAD
= 1mA, V
OUT
= 1.3V
V
IN
= 2V to 20V, I
LOAD
= 1mA, V
OUT
= 1.3V (Note 4)
I
LOAD
= 1mA to 500mA, V
IN
= 2V, V
OUT
= 1.3V
I
LOAD
= 1mA to 500mA, V
IN
= 2V, V
OUT
= 1.3V (Note 4)
V
SET
= 1.3V to 15V, V
IN
= 20V, I
LOAD
= 1mA
V
SET
= 1.3V to 15V, V
IN
= 20V, I
LOAD
= 1mA (Note 4)
V
SET
= 0V to 1.3V, V
IN
= 20V, I
LOAD
= 1mA
V
SET
= 0V to 1.3V, V
IN
= 20V, I
LOAD
= 1mA (Note 4)
I
LOAD
= 1mA, 50mA
l
ELECTRICAL CHARACTERISTICS
CONDITIONS
MIN
l
l
l
l
TYP
1.78
75
MAX
20
2
15
UNITS
V
V
mV
V
µA
µA
mA
2
0
99
98
100
100
2
–1
–2
0.5
0.5
3
0.1
30
0.03
150
0.3
220
220
101
102
l
l
l
l
l
l
l
l
1
2
±2
±3
0.5
400
0.6
600
2
275
330
280
350
350
450
4
5.5
7
25
mV
mV
nA/V
µV/V
nA
mV
nA
mV
nA
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
mA
mA
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
µV
RMS
µV
RMS
µV
RMS
nA
RMS
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
I
LOAD
= 300mA (Note 5)
l
I
LOAD
= 500mA (Note 5)
l
260
2.2
2.4
3.5
4.3
15
500
70
2
5
2.5
0.8
1.8
6
117
90
77
76
53
104
85
72
64
54
l
GND Pin Current
V
IN
= V
OUT(NOMINAL)
(Note 6)
I
LOAD
= 10µA
I
LOAD
= 1mA
I
LOAD
= 50mA
I
LOAD
= 100mA
I
LOAD
= 500mA
I
LOAD
= 500mA, Frequency = 10Hz, C
OUT
= 10µF, C
SET
= 0.47µF, V
OUT
= 3.3V
I
LOAD
= 500mA, Frequency = 10Hz, C
OUT
= 10µF, C
SET
= 4.7µF, 1.3V ≤ V
OUT
≤ 15V
I
LOAD
= 500mA, Frequency = 10kHz, C
OUT
= 10µF, C
SET
= 0.47µF, 1.3V ≤ V
OUT
≤ 15V
I
LOAD
= 500mA, Frequency = 10kHz, C
OUT
= 10µF, C
SET
= 0.47µF, 0V ≤ V
OUT
< 1.3V
I
LOAD
= 500mA, BW = 10Hz to 100kHz, C
OUT
= 10µF, C
SET
= 0.47µF, V
OUT
= 3.3V
I
LOAD
= 500mA, BW = 10Hz to 100kHz, C
OUT
= 10µF, C
SET
= 4.7µF, 1.3V ≤ V
OUT
≤ 15V
I
LOAD
= 500mA, BW = 10Hz to 100kHz, C
OUT
= 10µF, C
SET
= 4.7µF, 0V ≤ V
OUT
< 1.3V
l
l
l
l
Output Noise Spectral
Density (Notes 4, 8)
Output RMS Noise
(Notes 4, 8)
Reference Current RMS BW = 10Hz to 100kHz
Output Noise (Notes 4, 8)
Ripple Rejection
1.3V ≤ V
OUT
≤ 15V
V
IN
– V
OUT
= 2V (Avg)
(Notes 4, 8)
Ripple Rejection
0V ≤ V
OUT
< 1.3V
V
IN
– V
OUT
= 2V (Avg)
(Notes 4, 8)
EN/UV Pin Threshold
EN/UV Pin Hysteresis
V
RIPPLE
= 500mV
P-P
, f
RIPPLE
= 120Hz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 4.7µF
V
RIPPLE
= 150mV
P-P
, f
RIPPLE
= 10kHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 150mV
P-P
, f
RIPPLE
= 100kHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 150mV
P-P
, f
RIPPLE
= 1MHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 80mV
P-P
, f
RIPPLE
= 10MHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 500mV
P-P
, f
RIPPLE
= 120Hz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 50mV
P-P
, f
RIPPLE
= 10kHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 50mV
P-P
, f
RIPPLE
= 100kHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 50mV
P-P
, f
RIPPLE
= 1MHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
V
RIPPLE
= 50mV
P-P
, f
RIPPLE
= 10MHz, I
LOAD
= 500mA, C
OUT
= 10µF, C
SET
= 0.47µF
EN/UV Trip Point Rising (Turn-On), V
IN
= 2V
EN/UV Trip Point Hysteresis, V
IN
= 2V
1.18
1.24
130
1.32
V
mV
For more information
www.analog.com
3
Rev. C
LT3045
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C.
PARAMETER
EN/UV Pin Current
CONDITIONS
V
EN/UV
= 0V, V
IN
= 20V
V
EN/UV
= 1.24V, V
IN
= 20V
V
EN/UV
= 20V, V
IN
= 0V
l
l
l
l
l
l
l
l
l
ELECTRICAL CHARACTERISTICS
MIN
TYP
0.03
8
0.3
MAX
±1
15
1
10
20
850
430
550
110
309
UNITS
µA
µA
µA
µA
µA
µA
mA
mA
mA
mA • kΩ
mA
mA
mV
mV
nA
Quiescent Current in
V
IN
= 6V
Shutdown (V
EN/UV
= 0V) T
J
≤ 125°C (E/I-Grade)
T
J
≤ 150°C (H-/MP-Grade)
Internal Current Limit
(Note 12)
Programmable
Current Limit
PGFB Trip Point
PGFB Hysteresis
PGFB Pin Current
PG Output Low Voltage
PG Leakage Current
Reverse Input Current
Reverse Output Current
V
IN
= 2V, V
OUT
= 0V
V
IN
= 12V, V
OUT
= 0V
V
IN
= 20V, V
OUT
= 0V
Programming Scale Factor: 2V < V
IN
< 20V (Note 11)
V
IN
= 2V, V
OUT
= 0V, R
ILIM
= 300Ω
V
IN
= 2V, V
OUT
= 0V, R
ILIM
= 1.5kΩ
PGFB Trip Point Rising
PGFB Trip Point Hysteresis
V
IN
= 2V, V
PGFB
= 300mV
I
PG
= 100µA
V
PG
= 20V
V
IN
= –20V, V
EN/UV
= 0V, V
OUT
= 0V, V
SET
= 0V
V
IN
= 0, V
OUT
= 5V, SET = Open
570
230
450
90
291
710
700
330
150
500
100
300
7
25
l
l
l
30
100
1
100
mV
µA
µA
µA
µA
14
l
25
Minimum Load Required V
OUT
< 1V
(Note 13)
Thermal Shutdown
Start-Up Time
T
J
Rising
Hysteresis
V
OUT(NOM)
= 5V, I
LOAD
= 500mA, C
SET
= 0.47µF, V
IN
= 6V, V
PGFB
= 6V
V
OUT(NOM)
= 5V, I
LOAD
= 500mA, C
SET
= 4.7µF, V
IN
= 6V, V
PGFB
= 6V
V
OUT(NOM)
= 5V, I
LOAD
= 500mA, C
SET
= 4.7µF, V
IN
= 6V, R
PG1
= 50kΩ,
R
PG2
= 700kΩ (with Fast Start-Up to 90% of V
OUT
)
10ms Pulse
10
165
8
55
550
10
–0.01
°C
°C
ms
ms
ms
%/W
Thermal Regulation
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The EN/UV pin threshold must be met to ensure device operation.
Note 3:
Maximum junction temperature limits operating conditions. The
regulated output voltage specification does not apply for all possible
combinations of input voltage and output current, especially due to the
internal current limit foldback which starts to decrease current limit at
V
IN
– V
OUT
> 12V. If operating at maximum output current, limit the input
voltage range. If operating at the maximum input voltage, limit the output
current range.
Note 4:
OUTS ties directly to OUT.
Note 5:
Dropout voltage is the minimum input-to-output differential
voltage needed to maintain regulation at a specified output current. The
dropout voltage is measured when output is 1% out of regulation. This
definition results in a higher dropout voltage compared to hard dropout
— which is measured when V
IN
= V
OUT(NOMINAL)
. For lower output
voltages, below 1.5V, dropout voltage is limited by the minimum input
voltage specification.
For DFN package: Linear Technology is unable to
guarantee maximum dropout voltage specifications at high currents
due to production test limitations with Kelvin-sensing the package
pins.
Please consult the Typical Performance Characteristics for curves
of dropout voltage as a function of output load current and temperature
measured in a typical application circuit.
Note 6:
GND pin current is tested with V
IN
= V
OUT(NOMINAL)
and a current
source load. Therefore, the device is tested while operating in dropout. This
is the worst-case GND pin current. GND pin current decreases at higher
input voltages. Note that GND pin current does not include SET pin or ILIM
pin current but Quiescent current does include them.
Note 7:
SET and OUTS pins are clamped using diodes and two 25Ω series
resistors. For less than 5ms transients, this clamp circuitry can carry
more than the rated current. Refer to Applications Information for more
information.
Note 8:
Adding a capacitor across the SET pin resistor decreases output
voltage noise. Adding this capacitor bypasses the SET pin resistor’s
thermal noise as well as the reference current’s noise. The output noise
then equals the error amplifier noise. Use of a SET pin bypass capacitor
also increases start-up time.
4
Rev. C
For more information
www.analog.com
LT3045
ELECTRICAL CHARACTERISTICS
Note 9:
The LT3045 is tested and specified under pulsed load conditions
such that T
J
≈ T
A
. The LT3045E is 100% tested at 25°C and performance
is guaranteed from 0°C to 125°C. Specifications over the –40°C to 125°C
operating temperature range are assured by design, characterization, and
correlation with statistical process controls. The LT3045I is guaranteed
over the full –40°C to 125°C operating temperature range. LT3045H is
100% tested at the 150°C operating junction temperature. LT3045MP
is 100% tested and guaranteed over the full −55°C to 150°C operating
temperature range. High junction temperatures degrade operating lifetimes.
Operating lifetime is derated at junction temperatures greater than 125°C.
Note 10:
Parasitic diodes exist internally between the ILIM, PG, PGFB, SET,
OUTS, and OUT pins and the GND pin. Do not drive these pins more than
0.3V below the GND pin during a fault condition. These pins must remain at
a voltage more positive than GND during normal operation.
Note 11:
The current limit programming scale factor is specified while the
internal backup current limit is not active. Note that the internal current
limit has foldback protection for V
IN
– V
OUT
differentials greater than 12V.
Note 12:
The internal back-up current limit circuitry incorporates foldback
protection that decreases current limit for V
IN
– V
OUT
> 12V. Some level of
output current is provided at all V
IN
– V
OUT
differential voltages. Consult the
Typical Performance Characteristics graph for current limit vs V
IN
– V
OUT
.
Note 13:
For output voltages less than 1V, the LT3045 requires a 10µA
minimum load current for stability.
Note 14:
Maximum OUT-to-OUTS differential is guaranteed by design.
TI will create a new driving experience for the future with you - experience it yourself: The limited-time purchase of star products has begun~~Click here to enter the eventEvent time:From now until D...
The college entrance examination is an important answer sheet for everyone’s youth, a farewell, and a beginning.
I believe that after noon, the college entrance examination essay topics of various pro...
[i=s]This post was last edited by hehung on 2019-8-10 13:05[/i]I also have a GigaDevice board GD32F350. This time I tried to collect sensor data on this board. In fact, it is strictly the same as the ...
The transistor is used as a switching tube, but it introduces noise: I use a 9013 transistor as a switching tube, and observe the output signal with an oscilloscope. It introduces a lot of interferenc...
On August 24th, Tesla CEO Elon
Musk
revealed information about the upcoming FSD V14, claiming it will outperform human drivers. Tesla FSD lead Ashok stated last year that FSD version 12.5, ...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
On August 25th, TSMC, the world's leading contract chip manufacturer, attracted significant attention for its decision to build a chip manufacturing facility in Arizona. TSMC primarily manufactures...[Details]
White light LEDs are voltage-sensitive devices. In actual operation, their upper limit is 20mA. However, the current often increases due to various reasons during use. If no protective measures are...[Details]
1 Introduction
In the mid-1960s, American scientist Maas conducted extensive experimental research on the charging process of open-cell batteries and proposed an acceptable charging curve for ...[Details]
The Automotive Testing and Quality Assurance Expo (ATE 2025) will open on August 27th. At the expo, Rohde & Schwarz (R&S) will showcase six automotive testing solutions, themed "Intelligently Drivi...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
As AI accelerates across industries, the demand for data center infrastructure is also growing rapidly.
Keysight Technologies, in collaboration with Heavy Reading, released the "Beyo...[Details]
1. Ease of Use: The HMI module should be designed to be simple and clear, allowing users to easily operate and configure the energy storage device.
2. Ease of Maintenance: The HMI module should...[Details]
On August 22, according to CNBC's report today, the National Highway Traffic Safety Administration (NHTSA) is launching an investigation into Tesla, and the latter is questioned whether it has fail...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
Renesas Electronics' new ultra-low-power RA4C1 MCU features advanced security and a dedicated peripheral set, making it ideal for metering and other applications.
The new product mee...[Details]
I recently read an article in the Wall Street Journal titled "We need the right to repair our gadgets" (reference original article: ). The author was very angry about the phenomenon of "planned obs...[Details]
Driven by business opportunities such as access to new markets and government initiatives like the Belt and Road Initiative, global expansion has become a significant trend for Chinese companies. C...[Details]
The characteristics of electric vehicles place high demands on the motors they use. To increase top speed, the motor should have high instantaneous power and power density (W/kg); to increase drivi...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
