EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
LT3694-1 PINOUT IS SHOWN IN PARENTHESIS
FE PACKAGE
20-LEAD PLASTIC TSSOP
θ
JA
= 38°C/W
EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB
LT3694-1 PINOUT IS SHOWN IN PARENTHESIS
ORDER INFORMATION
LEAD FREE FINISH
LT3694EUFD#PBF
LT3694IUFD#PBF
LT3694EFE#PBF
LT3694IFE#PBF
LT3694-1EUFD#PBF
LT3694-1IUFD#PBF
LT3694-1EFE#PBF
LT3694-1IFE#PBF
TAPE AND REEL
LT3694EUFD#TRPBF
LT3694IUFD#TRPBF
LT3694EFE#TRPBF
LT3694IFE#TRPBF
LT3694-1EUFD#TRPBF
LT3694-1IUFD#TRPBF
LT3694-1EFE#TRPBF
LT3694-1IFE#TRPBF
PART MARKING*
3694
3694
LT3694FE
LT3694FE
36941
36941
LT3694FE-1
LT3694FE-1
PACKAGE DESCRIPTION
28-Lead (4mm
×
5mm) Plastic QFN
28-Lead (4mm
×
5mm) Plastic QFN
20-Lead Plastic TSSOP
20-Lead Plastic TSSOP
28-Lead (4mm
×
5mm) Plastic QFN
28-Lead (4mm
×
5mm) Plastic QFN
20-Lead Plastic TSSOP
20-Lead Plastic TSSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
36941fb
2
LT3694/LT3694-1
ELECTRICAL CHARACTERISTICS
PARAMETER
V
IN
Internal Undervoltage Lockout
Overvoltage Shutdown Threshold
Input Quiescent Current
Bias Quiescent Current
Shutdown Current
EN/UVLO Threshold, Bias On
EN/UVLO Threshold, Switching On
Reference Voltage Line Regulation
Switching Frequency
SYNC Input Frequency Range
V
IH
, SYNC
V
IL
, SYNC
V
OH
, CLKOUT
V
OL
, CLKOUT
PGOOD Output Voltage Low
PGOOD Leakage
PGOOD Threshold (Relative to V
FB
)
Switching Regulator
Feedback Pin Voltage
Feedback Pin Bias Current
Error Amplifier Transconductance
Error Amplifier Voltage Gain
TRK/SS Pull-Up Current
TRK/SS Threshold to Start Switching
V
C1
Source Current
V
C1
Sink Current
V
C1
Clamp Voltage
V
C1
Switching Threshold
V
C1
to Switch Current Gain
Switch Leakage Current
Minimum Boost Voltage Above Switch
Switch Current Limit (Note 3)
Switch V
CESAT
BST Operating Current
V
F
, BST Diode
I
L
BST Diode
DA Current Limit
Minimum Switch Off-Time
V
IN
= 36V
(Note 4)
(Note 3) 10% Duty Cycle
I
SW1
= 3A
I
SW1
= 3A
I
BST
= 100mA
V
BST
– V
BIAS
= 36V
l
l
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= 12V, V
BIAS
= 3V, unless otherwise noted. (Notes 2, 9)
CONDITIONS
l
l
MIN
3.5
36
TYP
3.8
38
1
2
0.1
MAX
4
40
2
3.5
2
1.23
1.1
2.5
0.35
UNITS
V
V
mA
mA
µA
mV
V
%/V
MHz
MHz
V
V
V
V
V
nA
%
mV
nA
µS
V/V
Not Switching
Not Switching
V
EN/UVLO
= 0.1V
350
1.16
0.9
0.25
1.5
1.6
5V < V
IN
< 36V
R
T
= 40.2k
LT3694 Only
LT3694 Only
LT3694 Only
I
CLKOUT
= –50µA, LT3694-1 Only
I
CLKOUT
= 50µA, LT3694-1 Only
I
PGOOD
= 250µA
V
PGOOD
= 2V
(Note 8)
86
735
l
l
l
l
l
l
500
1.2
0.01
1.0
2.6
0.3
0.2
10
90
750
–50
350
600
0.4
1000
94
765
–500
–2
35
V
C
= 0.6V
V
C
= 0.6V
–3
50
–20
28
2
0.75
3.6
0.01
1.8
–4
70
µA
mV
µA
µA
V
V
A/V
10
2.5
6
µA
V
A
mV
mA
V
µA
3.5
4.9
600
60
0.8
1
2.6
3.6
4.5
140
A
ns
36941fb
3
LT3694/LT3694-1
ELECTRICAL CHARACTERISTICS
PARAMETER
LDO Regulator
Feedback Pin Voltage
Feedback Pin Bias Current
Error Amplifier Voltage Gain
TRK/SS Pull-Up Current
TRK/SS Threshold to Shut Down LDO
Line Regulation
Load Regulation
Base Drive
Current Limit Threshold
Short-Circuit Current Limit Threshold
Minimum BIAS to DRV Voltage (Note 7)
Minimum V
IN
to DRV Voltage
V
FB
= 0
I
DRV
= 10mA
I
DRV
= 10mA
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= 12V, V
BIAS
= 3V, unless otherwise noted. (Notes 2, 9)
CONDITIONS
MIN
735
TYP
750
–50
2800
–2
35
5V < V
IN
< 36V
I
DRV
From 0.1mA to 10mA
l
l
MAX
765
–500
–4
70
UNITS
mV
nA
µA
mV
%/V
mV/mA
–3
50
0.025
0.5
10
47
22
15
60
26
0.3
2.0
20
70
30
0.9
2.3
mA
mV
mV
V
V
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT3694E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3694I is guaranteed to meet performance specifications from –40°C to
125°C junction temperature.
Note 3:
Current limit is guaranteed by design and/or correlation to static
test. Slope compensation reduces current limit at higher duty cycles.
Note 4:
This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions.
Junction temperature will exceed the maximum operating range when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair
device reliability.
Note 6:
Absolute Maximum Voltage at V
IN
and EN/UVLO pins is 70V for
non-repetitive, 1 second transients and 36V for continuous operation.
Note 7:
The LDO will function if the BIAS to DRV differential is not met,
but the base drive current will be drawn from V
IN
instead of BIAS.
Note 8:
The PGOOD pin will pull low when the voltage on any of the three
FB pins is lower than the PGOOD threshold value.
Note 9:
Positive currents flow into pins, negative currents flow out of pins.
Minimum and maximum values refer to absolute values.
I support domestic products. I bought a Meizu mobile phone. The SIM card slot broke in February. I didn't have a mobile phone to use at that time. I soldered the SIM card to the soldering point of the...
Previously, in order to bring out the relevant signal lines, a matching expansion board for SHT31 was specially drawn. At the same time, the space on the expansion board was used to add a lithium batt...
As the name suggests, the LMZ10501 module is the first series of power modules. The maximum working input voltage is 5.5V and the output current is 1A. In addition, the supply voltage of the power mod...
All those who participate in the video learning and take the "qualification exam" with a score of 60 or above in the C2000 boutique course event can purchase the C2000 LaunchPad development board at a...
[i=s]This post was last edited by oJingtiano on 2020-4-15 11:45[/i]I am a beginner and I am currently learning the relationship between pointers and functions. I have written a function whose return v...
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
