Global Configuration Register ............................................................................................................................... 60
Active Analog Temperature Sensors ..................................................................................................................... 66
Direct ADC Measurements .................................................................................................................................... 70
2- and 3-Cycle Conversion Modes ........................................................................................................................ 75
Running Conversions Consecutively on Multiple Channels................................................................................... 75
Related Parts .....................................................................................................................90
29861fa
2
For more information
www.linear.com/LTC2986
LTC2986/LTC2986-1
ABSOLUTE MAXIMUM RATINGS
(Notes 1, 2)
PIN CONFIGURATION
TOP VIEW
GND
V
REF_BYP
NC
GND
V
DD
GND
V
DD
GND
V
DD
GND
V
DD
GND
13
14
15
16
17
18
19
20
21
22
23
24
12
11
10
9
8
7
6
5
4
3
2
1
LX PACKAGE
48-LEAD (7mm
×
7mm) PLASTIC LQFP
T
JMAX
= 150°C,
θ
JA
= 57°C/W
ORDER INFORMATION
LEAD FREE FINISH
LTC2986CLX#PBF
LTC2986ILX#PBF
LTC2986HLX#PBF
LTC2986CLX-1#PBF
LTC2986ILX-1#PBF
LTC2986HLX-1#PBF
TRAY
LTC2986CLX#PBF
LTC2986ILX#PBF
LTC2986HLX#PBF
LTC2986CLX-1#PBF
LTC2986ILX-1#PBF
LTC2986HLX-1#PBF
http://www.linear.com/product/LTC2986#orderinfo
PART MARKING*
LTC2986LX
LTC2986LX
LTC2986LX
LTC2986LX-1
LTC2986LX-1
LTC2986LX-1
PACKAGE DESCRIPTION
48-Lead (7mm
×
7mm) LQFP
48-Lead (7mm
×
7mm) LQFP
48-Lead (7mm
×
7mm) LQFP
48-Lead (7mm
×
7mm) LQFP
48-Lead (7mm
×
7mm) LQFP
48-Lead (7mm
×
7mm) LQFP
TEMPERATURE RANGE
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
CH10
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
COM
25
26
27
28
29
30
31
32
33
34
35
36
Supply Voltage (V
DD
) ................................... –0.3V to 6V
Analog Input Pins (CH1 to
CH10, COM) ................................. –0.3V to (V
DD
+ 0.3V)
Input Current (CH1 to CH10, COM) ...................... ±15mA
Digital Inputs (CS, SDI,
SCK,
RESET)
................................ –0.3V to (V
DD
+ 0.3V)
Digital Outputs (SDO, INTERRUPT) –0.3V to (V
DD
+ 0.3V)
V
REFP
........................................................ –0.3V to 2.8V
Identification and testing of electronic components - introductory improvement chapter Different electronic components have different performance and parameter requirements. Mastering the identificati...
Is the output of aic23 the sampling value of the sound waveform, or is it the encoded or compressed data? When I draw the data into a waveform, it doesn't look like a sound signal, and of course I can...
[font=微软雅黑][size=4]According to the EEWORLD moderator rules and moderator operation manual, the list of moderators who received awards in January 2016 is as follows: [/size][/font][/align][align=left]...
When developers choose RTOS for embedded products , real-time performance is one of the most important criteria. The latest research report from embedded market research companies Evans Data and Ventu...
Hello, seniors! I recently encountered the problem of not being able to connect to NK.lib when compiling the OAL of WINCE5.0. I learned from the help file of PB5.0 that NK.lib is composed of Cefnk.lib...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
The serial interface real-time clock chip DS1302 launched by Dallas Company in the United States can trickle charge the backup battery of the clock chip. Due to the main features of the chip such a...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Portable power applications are broad and varied. Products range from wireless sensor nodes with average power consumption of only a few microwatts to in-vehicle medical or data acquisition systems...[Details]
At present, with the diversification of portable products and the almost harsh requirements for audio and video parts, the power consumption requirements of the whole machine have been raised to a ...[Details]
It should be understood as follows: DC-DC means direct current to direct current (conversion of different DC power values). Anything that meets this definition can be called a DC-DC converter, incl...[Details]
1 Introduction
Automatic Test
System The ATS (Automatic Test System) integrates all the stimulus and measurement equipment required for testing.
The computer
efficiently comp...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
