EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB GND
MSE PACKAGE
12-LEAD PLASTIC MSOP
T
JMAX
= 150°C,
θ
JA
= 40°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB GND
orDer inForMaTion
LEAD FREE FINISH
LTC3245EDE#PBF
LTC3245IDE#PBF
LTC3245EMSE#PBF
LTC3245IMSE#PBF
LTC3245HMSE#PBF
LTC3245MPMSE#PBF
TAPE AND REEL
LTC3245EDE#TRPBF
LTC3245IDE#TRPBF
LTC3245EMSE#TRPBF
LTC3245IMSE#TRPBF
LTC3245HMSE#TRPBF
LTC3245MPMSE#TRPBF
PART MARKING*
3245
3245
3245
3245
3245
3245
PACKAGE DESCRIPTION
12-Lead (3mm
×
4mm) Plastic DFN
12-Lead (3mm
×
4mm) Plastic DFN
12-Lead Plastic MSOP
12-Lead Plastic MSOP
12-Lead Plastic MSOP
12-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
elecTrical characTerisTics
SYMBOL
V
IN
V
UVLO
PARAMETER
Operating Input Voltage Range
V
IN
Undervoltage Lockout Threshold
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C, (Note 2). V
IN
= 12V, V
OUT
= 5V, C
FLY
= 1µF unless otherwise
noted.
CONDITIONS
l
MIN
2.7
l
TYP
2.4
2.2
MAX
38
2.7
UNITS
V
V
V
3245fa
V
IN
Rising
V
IN
Falling
2
For more information
www.linear.com/LTC3245
LTC3245
elecTrical characTerisTics
SYMBOL
I
VIN
PARAMETER
V
IN
Quiescent Current
SEL1 = SEL2 = 0V
V
OUT
Enabled,
BURST
= 0V
V
OUT
Enabled,
BURST
= V
IN
Fixed 5V Burst Mode Output Regulation
(OUTS/ADJ Connected to V
OUT
,
BURST
= 0V, SEL2 = V
IN
, SEL1 = 0V)
(Note 5)
Fixed 5V Low Noise Output Regulation
(OUTS/ADJ Connected to V
OUT
,
BURST
= V
IN
, SEL2 = V
IN
, SEL1 = 0V)
(Note 5)
Fixed 3.3V Burst Mode Output Regulation
(OUTS/ADJ Connected to V
OUT
,
BURST
= 0V, SEL2 = V
IN
, SEL1 = V
IN
)
(Note 5)
Fixed 3.3V Low Noise Output Regulation
(OUTS/ADJ Connected to V
OUT
,
BURST
= V
IN
, SEL2 = V
IN
, SEL1 = V
IN
)
(Note 5)
OUTS/ADJ Reference Voltage (Note 4)
Load Regulation (Referred to ADJ)
PGOOD Rising Threshold
PGOOD Falling Threshold
PGOOD Output Low Voltage
PGOOD Output High Leakage
BURST,
SEL1, SEL2 Input Voltage
BURST,
SEL1, SEL2 input Voltage
BURST,
SEL1, SEL2 Input Current
BURST,
SEL1, SEL2 Input Current
I
VOUT
Short-Circuit Current
Charge Pump Output Impedance
Oscillator Frequency
V
PIN
= 0V
V
PIN
= 38V
V
OUT
= GND
2:1 Step-Down Mode
1:1 Step-Down Mode
1:2 Step-Up Mode (V
IN
= 3.3V)
l
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C, (Note 2). V
IN
= 12V, V
OUT
= 5V, C
FLY
= 1µF unless otherwise noted.
CONDITIONS
Shutdown, V
OUT
= 0V
CP Enabled, Output in Regulation
CP Enabled, Output in Regulation
5V ≤ V
IN
< 38V, I
OUT
≤ 250mA
4V ≤ V
IN
< 5V, I
OUT
≤ 150mA
3.3V ≤ V
IN
< 4V, I
OUT
≤ 75mA
3V ≤ V
IN
< 3.3V, I
OUT
≤ 45mA
5V ≤ V
IN
< 38V, I
OUT
≤ 200mA
4V ≤ V
IN
< 5V, I
OUT
≤ 120mA
3.3V ≤ V
IN
< 4V, I
OUT
≤ 60mA
3V ≤ V
IN
< 3.3V, I
OUT
≤ 35mA
5V ≤ V
IN
< 38V, I
OUT
≤ 250mA
4V ≤ V
IN
< 5V, I
OUT
≤ 175mA
3.3V ≤ V
IN
< 4V, I
OUT
≤ 110mA
2.7V ≤ V
IN
< 3.3V, I
OUT
≤ 60mA
5V ≤ V
IN
< 38V, I
OUT
≤ 220mA
4V ≤ V
IN
< 5V, I
OUT
≤ 140mA
3.3V ≤ V
IN
< 4V, I
OUT
≤ 90mA
2.7V ≤ V
IN
< 3.3V, I
OUT
≤ 50mA
SEL2 = 0V, SEL1 = V
IN
, I
OUT
= 0mA
SEL2 = 0V, SEL1 = V
IN
V
OUT
% of Final Regulation Voltage
V
OUT
% of Final Regulation Voltage
I
PGOOD
= 0.2mA
V
PGOOD
= 5V
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
MIN
TYP
4
18
20
MAX
8
35
40
5.2
5.2
5.2
5.2
5.2
5.2
5.2
5.2
3.43
3.43
3.43
3.43
3.43
3.43
3.43
3.43
UNITS
µA
µA
µA
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
mV/mA
%
%
V
µA
V
V
µA
µA
mA
Ω
Ω
Ω
V
OUT5_BM
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
3.17
3.17
3.17
3.17
3.17
3.17
3.17
3.17
1.176
1.200
0.2
95
88
–1
0.4
–1
0.5
91
0.1
0
0.9
1.2
0
1
900
3
3.5
14
450
V
OUT5_LN
V
OUT33_BM
V
OUT33_LN
V
ADJ
R
CL
V
PG_RISE
V
PG_FALL
V
PG_LOW
I
PG_HIGH
V
LOW
V
HIGH
I
LOW
I
HIGH
I
SHORT_CKT
R
OUT
f
OSC
1.224
98
0.4
1
2
1
3
500
kHz
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime. This IC has overtemperature protection that is
intended to protect the device during momentary overload conditions.
Junction temperatures will exceed 150°C when overtemperature is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
Note 2:
The LTC3245E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 125°C operating junction
temperature range are assured by design, characterization and correlation
with statistical process controls. The LTC3245I is guaranteed over the
–40°C to 125°C operating junction temperature range. The LTC3245H is
guaranteed over the –40°C to 150°C operating junction temperature range
and the LTC3245MP is tested and guaranteed over the full –55°C to 150°C
operating junction temperature range. High junction temperatures degrade
operating lifetimes; operating lifetime is derated for junction temperatures
greater than 150°C. Note that the maximum ambient temperature consistent
with these specifications is determined by specific operating conditions in
conjunction with board layout, the rated package thermal resistance and
other environmental factors.
Note 3:
The junction temperature (T
J
, in °C) is calculated from the ambient
temperature (T
A
, in °C) and power dissipation (P
D
, in Watts) according to
the formula:
T
J
= T
A
+ (P
D
•
θ
JA
) where
θ
JA
(in °C/W) is the package thermal
impedance.
Note 4:
V
OUT
programming range is from 2.5V to 5V. See the
Programming the Output Voltage section for more detail.
Note 5:
The maximum operating junction temperature of 150°C must be
followed. Certain combinations of input voltage and output current will
cause the junction temperature to exceed 150°C and must be avoided. See
Thermal Management section for information on calculating maximum
Air quality detectors are not new. In fact, we all have one on our faces. Unfortunately, our noses are sometimes unreliable, failing to detect odorless harmful gases or when a fire breaks out nearby w...
I recently installed CCS5.1, but found that it starts up much slower than CCS3, and the burning process is also much slower. Does anyone have a solution?...
I just learned freecalce microcontroller, a development board of DZ60, the external crystal is 8M, and I wrote the simplest running light code. The function can be realized, but there are some problem...
[font=Verdana][size=3]40 experiments for beginners of single-chip microcomputers, word format, a total of 205 pages, very practical information, welcome to download.[/size][/font][p=21, null, center][...
While
the solid-state battery
industry is still engaged in a long technological marathon for
the "ultimate solution" for
electric vehicles
, some companies have begun looking for mor...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
Multi-touch mobile phone
Multi-touch is a system that can respond to multiple touches on the screen at the same time. Multi-touch phones are divided into capacitive and resistive types. Capaci...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
The mobile computing market is rapidly evolving, and manufacturers are fiercely competing for market share. A key area of competition is battery life, which encompasses two key aspects: how long th...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
introduction
With the development of the information superhighway and the internet, broadcast television has become increasingly widespread worldwide. Television information has emerged in var...[Details]
As the core of electric vehicles, batteries are concerned with vehicle use and maintenance. The operation of vehicles is guaranteed by the electricity generated by batteries. For batteries, battery...[Details]
introduction
Due to their flexibility and security, Java cards are increasingly being used in the smart card field. Once a Java card is released, if multiple applications need to call the same...[Details]
Automotive electronics is a general term for both vehicle-mounted and onboard electronic control devices. Automotive electronics is considered a revolution in automotive technology, and its degree ...[Details]
With the increasing awareness of environmental protection and the tightening of emission regulations and standards, almost all car companies are moving towards new energy, whether they are internat...[Details]
Demonstrating Ceva’s technological leadership and deep collaboration with industry partners for over two decades,
To meet the industry's accelerating demand for ubiquitous edge AI
...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
