EEWORLDEEWORLDEEWORLD

Part Number

Search

BTB-45-01-T-S-270

Description
Board Connector, 45 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size292KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Download Datasheet Parametric View All

BTB-45-01-T-S-270 Overview

Board Connector, 45 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BTB-45-01-T-S-270 Parametric

Parameter NameAttribute value
MakerSAMTEC
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPCB STACKING CONNECTOR
body width0.079 inch
subject depth0.17 inch
body length3.555 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial numberBTB
Plug contact pitch0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness150u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts45
What a terrible early morning.
Around 2 a.m. today, I walked outside the building and was shocked by the scene in front of me. Oh my god, thick smoke and dust covered the earth. I have been here for some time. I have never seen suc...
ienglgge Talking
Help bdata
I defined a BDATA like this, uint bdata port; port^0=P3^5; port^1=P3^6; port^2=P3^7; port^3=P2^6; port^4=P2^7; port^5=P1^6; I want to use it to operate the port of the microcontroller, but it doesn't ...
renyunpei 51mcu
How to compare the hierarchical schematics (multiple schematics correspond to one PCB) in AD software to show the differences between the schematics and PCB?
As the title says, after using AD software to design a board with multiple schematics corresponding to one PCB, how can I compare the differences between the schematics and the PCB? I only know how to...
yjguohua PCB Design
There is a strange phenomenon at the MCU IO port, please help!
Hello everyone! The microcontroller I use is C8051F020. There are problems with my three IO ports. The IO ports are set to open drain state, and the cross switch is also fine. There are no digital per...
shi991 Embedded System
Change the 51 microcontroller infrared remote control program into a program that can run in the Arduino compilation environment
I am a beginner and I am confused about the program of single-chip microcomputer. I want to use infrared remote control to control a robot. The board is Arduino 2009 MEGA168, crystal oscillator 16M, b...
34747124 Robotics Development
Repost: Cui Yongyuan wrote to the president of the Agricultural University and proposed a debate on GMOs in front of students
Since I am basically ignorant about GMOs, the reposting does not necessarily represent my own views. However, I still think that the current science and technology may not be able to make a definitive...
wangfuchong Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 247  1591  2848  1685  282  5  33  58  34  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号