Please refer to the M5600_U5600 Installation Manual and M5600_U5600 Software Manual.
Note:
Communication is max 65 feet
TE CONNECTIVITY SENSORS
/// M5600
09/2017
Page 3
M5600
Wireless Pressure Transducer
ORDERING INFORMATION
M5600
–
0 0 0 0 0 2
–
05KP G
Port Material
0
17-4PH
1
316L Stainless Steel
Cleaning
0
No Selection
1
Oxygen clean B40.1 Level IV
2
With Snubber
Battery
0
Without Battery
1
CR2032
2
CR2050
Label Type
0
Adhesive Label
1
Laser Marking
Pressure Port
2
1/4-19 BSPP
3
G3/8 JIS B2351
7/16-20UNF Male SAE J1326-2
4
Straight Thread O-Ring BUNA-N
90SH-904
5
1/4-18 NPT
6
1/8-27 NPT
B
G1/4 JIS B2351
E
1/4-19 BSPT
F
1/4-19 BSPP Female w/o Snubber
7/16-20 UNF Female SAE J513
P
Straight Thread
7/16-20 UNF Female SAE J513
N
Straight Thread
M10x1.0mm
Q
ISO 6149-2
M12x1.5mm
S
ISO 6149-2
G1/4 DIN 3852 Form E Gasket
U
DIN3869-14 NBR
M20x1.5mm
W
ISO6149-2
M14x1.5mm
G
ISO6149-2
Pressure Type
G
Gauge
S
Sealed
C
Compound
Compound pressure range is -14.7 to xxxpsig or -1 to xxxbarg.
(e.g. 200PC: -14.7 to 200psig, 020BC: -1 to 20barg)
Pressure Range [psi]
psi
STD
050P
100P
200P
300P
500P
01KP
03KP
05KP
07KP
10KP
15KP
bar
STD
3.5B
007B
010B
020B
035B
070B
200B
350B
500B
700B
01KB
NORTH AMERICA
Measurement Specialties, Inc.,
a TE Connectivity Company
Phone: 800-522-6752
Email:
customercare.frmt@te.com
EUROPE
Measurement Specialties (Europe), Ltd.,
a TE Connectivity Company
Phone: +31 73 624 6999
Email:
customercare.lcsb@te.com
ASIA
Measurement Specialties (China), Ltd.,
a TE Connectivity Company
Phone: 0400-820-6015
Email:
customercare.shzn@te.com
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
[i=s]This post was last edited by 416202554 on 2015-3-25 18:51[/i] 1.LFXT -> ACLK, 32768Hz, BRCLK -> ACLK, baud rate 9600, works normally in LPM3 mode; (due to project requirements, the baud rate need...
I called the ActivateDeviceEx function to dynamically load the DLL driver I wrote. ActivateDeviceEx() corresponds to the XXX_Init() function, but when calling the ActivateDeviceEx function, not only t...
[b]1. The output power of the half-bridge transformer switching power supply is very large and the working efficiency is very high [/b] The half-bridge transformer switching power supply is the same a...
1. Low comprehensive cost, only one-time investment is required, no trenching and pipe laying is required, and it is especially suitable for outdoor places with long distance and well-decorated. In ma...
The receiving module has 3 pins, VCC+ DATA output GND- DATA output is TTl output. How to connect it so that the output is a pure signal? Suppose a remote control is pressed and the transmitting module...
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
