227Y0112S220ME datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> 227Y0112S220ME

227Y0112S220ME: DescriptionRotary Switch, 12 Positions, SP12T, Latched, 1A, 28VDC, Solder Terminal, Through Hole-right Angle, ROHS COMPLIANT; CategoryMechanical and electronic products switch; File Size333KB，3 Pages; ManufacturerCTS; Environmental Compliance

Download Datasheet Parametric View All

227Y0112S220ME Overview

Rotary Switch, 12 Positions, SP12T, Latched, 1A, 28VDC, Solder Terminal, Through Hole-right Angle, ROHS COMPLIANT

227Y0112S220ME Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	unknow
ECCN code	EAR99
Body length or diameter	36.6 mm
Contact (AC) maximum rated R load	.75A@125VAC
Maximum contact current (AC)	0.75 A
Maximum contact current (DC)	1 A
Contact (DC) maximum rated R load	1A@28VDC
Maximum contact voltage (AC)	125 V
Maximum contact voltage (DC)	28 V
Electrical life	25000 Cycle(s)
Graduation angle	30 deg
JESD-609 code	e4
Manufacturer's serial number	227Y
Installation features	THROUGH HOLE-RIGHT ANGLE
Number of positions	12
Number of switching segments	1
surface mount	NO
Switch action	LATCHED
switch function	SP12T
Switch type	ROTARY SWITCH
Terminal surface	Silver (Ag)
Termination type	SOLDER
Base Number Matches	1

Preview

Download Datasheet

View All

Series 227

Data Sheet

Electrocomponents

Rotary Switch

Industrial

Features

• Hill and valley detent

• Enclosed diecast detent plate

• Low cost

• 30˚ indexing

Rotary Switch

• Solder lug and printed circuit terminals available

• Molded stator prevents solder from flowing into

the circuit

• Custom switching patterns available

• Index or wafers are available separately

• RoHS compliant

Electrical and Mechanical Specifications

Indexing

Double bump spring hill and valley detent with

30° indexing for 2 through 12 positions or

continuous rotation.

Voltage and Contact Rating

UL Rating: 3/4 amp at 125 VAC (shorting type only)

Special Rating: 1/4 amp at 28 VDC (shorting or non shorting)

1 amp at 28 VDC (shorting type only)

Contact Resistance

.015 ohm max. when measured from adjacent terminals

Stop Strength

15 in-lb (17.3 Kgf-cm)

Torque

As required within a range of 10 in-oz. (720 gf-cm)

to 60 in-oz. (4.3 Kgf-cm)

Detent Rotational Life

25,000 cycles

Materials

Shaft: Aluminum or brass at CTS option

Bushing: Brass or Zinc diecast at CTS option

Detent Spring: Stainless steel

Detent Plate: Zinc diecast

Rotor Contacts, Stator Contacts and Terminals:

Silver plated brass standard

Stator Insulator: Glass reinforced thermoset material

Bushing Lengths

Standard: 3/8"-32 UNEF-2A Thread,1/4" (6.35mm)

or 3/8" (9.53mm) long.

Special Lengths: Available as required

Locating Lugs

Standard: Left side .531" (13.5mm) radius

Special: Right side .531" (13.5mm) radius or no lug

Shaft Trim

Standard: Plain round, Flat, Slot, Knurl, or mixed (Flat with Slot)

Special: Available as required

Frames

Machine screw, or staked strut (up to 3 wafers only)

Technical Data Sheet 1448C

1-3

CTS Electrocomponents

09/13/09

www.ctscorp.com

Recommended Resources

TW-42 ultra-short wave radio transmitter high frequency power amplifier circuit part

Use 811A tube to make 10W final power amplifier

High Efficiency Negative Voltage Regulator Circuit

A734 type double-sided yarn machine electrical control improved circuit

Enhanced stereo effect four-channel amplifier.gif

AM receiver AGC circuit

Please help me, please help me check this print driver.: void PrintOneChar(void) { uchar Temp; uchar i; bPrintTimer0=0; Temp=0; Stb=1; //Set high strobe line Busy=1; //Busy input for(i=1;i>0;i --); while(Busy) //Printer is busy, wait {if((bPrintTimer0-Temp)...; zpfst Embedded System

Operational Amplifier Noise: Hello everyone, I recently encountered a problem when working on an amplifier. How to convert the amplifier noise nv/HZ (1/2) into dBm? The signal I amplified comes from the RF mixer, and my intermedi...; 小海不怕 Analogue and Mixed Signal

Replace the Sony Z1 internal battery yourself: One day my Z1 turned into this without warning, I was shocked at the moment, and after a closer look, I found that the battery was pregnant, and it actually pushed the back cover open.At this time, I ...; Shadow_wong Making friends through disassembly

I'd like to ask, does anyone know what I can use to replace the MX7452 video processing chip?: I have been searching for a long time but have not found any replacement solution for this chip. I am so confused....; Mr.HH Integrated technical exchanges

Circuit Design_Buzzer Tips: [size=4][color=rgb(51, 51, 51)][font=Helvetica,]Buzzers are divided into two categories: piezoelectric and electromagnetic. [/font][/color][color=#333333][/color][/size][color=rgb(51, 51, 51)][font=He...; fish001 Analogue and Mixed Signal

Op amp zeroing problem: I made a logarithmic circuit for UA741. When I adjust the zero, the reading of the digital multimeter keeps changing. What is the reason? Please give me some advice. I am so anxious....; bluesky4016 Analog electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components