EEWORLDEEWORLDEEWORLD

Part Number

Search

59112-R38-03-037

Description
Board Connector, 6 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator
CategoryThe connector    The connector   
File Size203KB,2 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

59112-R38-03-037 Overview

Board Connector, 6 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator

59112-R38-03-037 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Objectid308029532
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.157 inch
subject depth0.146 inch
body length0.236 inch
Connector typeBOARD CONNECTOR
Contact completed and terminatedMatte Tin (Sn)
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage650VAC V
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number59112
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
Plating thickness15u inch
Rated current (signal)2 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.098 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts6
w wcadmin
Guo-Min Sun
-
Rick Bian
2010/10/31
2013/12/12
-
2013/12/12
ELX-N-16500-1
Released
N
PDS: Rev :N
STATUS:Released
Printed: Dec 12, 2013
Application of DSP repetitive control technology in inverter power supply system
This paper proposes a DSP repetitive control scheme, which uses a repetitive controller to track the periodic reference command signal, reduce the output voltage harmonics, and improve the dynamic per...
Jacktang DSP and ARM Processors
The problem of PCB parasitic capacitance
[i=s] This post was last edited by S3S4S5S6 on 2017-11-9 08:48 [/i] An oscillation circuit was built using TLV3501 according to the typical application in the manual. After PCB layout, it was found th...
S3S4S5S6 PCB Design
Why can the reference layer of PCB also be the power layer?
As shown in the figure above, in a 4-layer PCB stack, why can the differential line refer to the third layer (Power layer)? I understand that ordinary single-ended signals must be referenced to the gr...
xiaominwzj PCB Design
I drew the schematic using protues software, and after converting it into a PCB diagram, I found that only the buzzer was not packaged.
I finished drawing the schematic diagram using protues software. After converting it into PCB diagram, I found that only the buzzer was not packaged. After checking online, I found that I had to draw ...
圈在指尖 PCB Design
Questions about SPI in 5438
The direction of the signal on the middle line is from slave to master. Does it mean that the slave controls the UCxSTE bit of the master? But I think it should be manually decided in the program whet...
zzbaizhi Microcontroller MCU
Basic knowledge of automobile body design
This article provides some basic knowledge of automobile body design, which is suitable for learning and training of relevant departments in the automobile industry. Main contents: Main components of ...
frozenviolet Automotive Electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1110  1022  2319  969  1603  23  21  47  20  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号