EEWORLDEEWORLDEEWORLD

Part Number

Search

3KH70/9JNK1(081)

Description
Card Edge Connector, 140 Contact(s), 2 Row(s), Straight, 0.1 inch Pitch, Solder Terminal, Hole .125-.137, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size535KB,5 Pages
ManufacturerWPI Viking Electronics Inc.
Download Datasheet Parametric View All

3KH70/9JNK1(081) Overview

Card Edge Connector, 140 Contact(s), 2 Row(s), Straight, 0.1 inch Pitch, Solder Terminal, Hole .125-.137, Black Insulator, Receptacle,

3KH70/9JNK1(081) Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresNONE
Board mount optionsMOUNTING FLANGE
body width0.37 inch
subject depth0.61 inch
body length7.835 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationAU ON NI
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleBELLOWED TYPE
Dielectric withstand voltage650VAC V
maximum insertion force2.78 N
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED PHENOLIC
MIL complianceYES
Manufacturer's serial numberJNK
Plug contact pitch0.1 inch
Installation option 1HOLE .125-.137
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing5.08 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityMIL-C-21097
Terminal length0.165 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts140
Evacuation force-minimum value.278 N
Calculate optical power
How to calculate optical power from voltage...
jinger0311 Analog electronics
How to realize the superposition of two DC voltage signals
Now I want to add a small voltage of 1 volt to a variable control voltage signal Vctro (2.6-26) to make the output change between 3.6-27 volts. I should use an op amp. I want to find one with small te...
dandan5241 Analog electronics
Show off the MPLAB Starter Kit for PIC18 I just bought
[i=s]This post was last edited by lcofjp on 2014-5-27 07:16[/i] Microchip 5.1 was on sale, and I couldn't resist the temptation and bought the MPLAB Starter Kit for PIC18 MCUs (DM180021). The main chi...
lcofjp Microchip MCU
When the software is reset, the FLASH interrupt vector table will be cleared
When I am doing write protection and release protection, I need to reset the software. However, when using KEIL online debugging, the data in the FLASH interrupt vector table will be cleared to zero. ...
zhufu201 stm32/stm8
LPC_CMSIS
This is my first time to use ARM Cortex. I'm going to publish a software interface standard for M0/M3, which mainly includes standard startup code, kernel and on-chip peripheral .H definitions, etc. I...
caine1012 NXP MCU
Problems with uboot calling kernel under ARM
I've been learning about porting recently, but I've encountered a lot of difficulties. For example, kernel porting. I can make sure that there are no problems with uboot and fs, and then compile the k...
lanhaiyizhen ARM Technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 58  2208  2458  634  1067  2  45  50  13  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号