a. Device mounted with all leads soldered or welded to PC board.
b. Derate 5.5 mW/_C above T
A
= 70_C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Typical values for dropout voltage at V
OUT
w
2 V are measured at
V
OUT
= 3.3 V, while typical values for dropout voltage at V
OUT
< 2 V are measured at V
OUT
= 1.8 V.
d. Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the output voltage measured with a 1-V
differential, provided that V
IN
does not not drop below 2.0 V.
e. Ground current is specified for normal operation as well as “drop-out” operation.
f.
The device’s shutdown pin includes a typical 2-MW internal pull-down resistor connected to ground.
g. V
OUT(nom)
is V
OUT
when measured with a 1-V differential to V
IN.
TIMING WAVEFORMS
V
IN
V
SD
t
r
v
1
ms
0V
t
ON
V
NOM
0.95 V
NOM
V
OUT
FIGURE 1.
Timing Diagram for Power-Up
Document Number: 71447
S-40592—Rev. C, 29-Mar-04
www.vishay.com
3
Si91841/3
Vishay Siliconix
PIN CONFIGURATION
PIN DESCRIPTION
V
OUT
Thin SOT-23, 5-Lead
V
IN
1
5
Pin No.
1
2
Name
V
IN
GND
SD
BP
V
OUT
Function
Input supply pin. Bypass this pin with a 1-mF ceramic or tantalum capacitor to ground
Ground pin. For better thermal capability, directly connected to large ground plane
By applying less than 0.4 V to this pin, the device will be turned off. Connect this pin to
V
IN
if unused
Noise bypass pin. For low noise applications, a 0.01
IoT communication technology is divided into wired and wireless, and different communication methods are used according to different application scenarios and needs.
Wired communicationWired communica...
Students
Let’s share more and learn and improve together.
launchpad
Low supply voltage range: 1.8V to 3.6V Ultra-low power consumption – Run mode: 230μA (at 1MHz and 2.2V ) – Standby mode: 0.5μA – Off...
[i=s]This post was last edited by bluefox0919 on 2019-1-2 17:30[/i] I have an old project on hand. The original designer has left the company for many years... I need to solve the ESD. The appearance ...
The strain gauge bridge has a zero output of 4mV, a full-scale output of about 4.5mV, and a full-scale output change of 0.5mV, but the zero offset is as high as 4mV;zero offset compensation solution:1...
Urgent question! Experts, please help me. In wince, my program is written in evc4.0. When communicating with the target machine, I am the client and the target machine is the server. The onclose in CC...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Electric bicycles have long been a means of transportation for lower-income groups due to their affordability. The largest concentrated expense in the use of electric vehicles is the cost of replac...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]