EEWORLDEEWORLDEEWORLD

Part Number

Search

WCTN26322301B

Description
RES NET,THIN FILM,22.3K OHMS,100WV,.1% +/-TOL,-10,10PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

WCTN26322301B Overview

RES NET,THIN FILM,22.3K OHMS,100WV,.1% +/-TOL,-10,10PPM TC,0303 CASE

WCTN26322301B Parametric

Parameter NameAttribute value
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance22300 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient-10,10 ppm/°C
Tolerance0.1%
Operating Voltage100 V
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
①After F2812 XINT1 interrupt, the program always runs away? ?
There are two questions:1. Why do we need to enable group1 interrupt (① in the code below) and general interrupt enable (② in the code below) again in the interrupt function of xint1 even if the inter...
lylnk Microcontroller MCU
500 V Common Mode Voltage Current Monitor
The article "ADI Award-winning Download - Solar Photovoltaic Power Generation Solutions" mentions several very distinctive circuits of ADI, the 500 V common-mode voltage and current monitor AD8212, an...
dontium ADI Reference Circuit
A disassembled emergency light found on the Internet
These few days, I will find some relevant reference materials for our activities and prepare to participate in them.I found a picture of my buddy violently disassembling the emergency light. I'm repos...
clark DIY/Open Source Hardware
STC single chip computer frequency measurement problem
I use STC microcontroller to measure frequency (0-26HZ). The frequency signal is introduced by external interrupt 1-INT1, using falling edge trigger mode, and TIMER1 measures the time between two fall...
lvyu55 Embedded System
CCS compiles and generates binary files
The default file generated by CCS is in coff format. The default .out file is in this file format. If you want to generate binary files, set CCS as follows. 1. Project-right click-show build settings....
fish001 DSP and ARM Processors
Where can I find information about DHCP CLIENT?
I want to develop a DHCP client on VxWorks. Where can I find information on this? Thank you....
ayangyzl Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2321  2401  1413  192  2179  47  49  29  4  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号