This IC is a reset IC for turning on/off power supply and power flicker in CPU or logic systems.
This IC can change delay time by an external capacitor.
Features
1.
2.
3.
4.
5.
6.
7.
8.
9.
Maximum supply voltage
Detecting voltage accuracy
Low supply current
Operating supply voltage
Operating temperature
Reset voltage rank
Reset temperature coefficient
Delay Resistance
Output type
7V
±1.0%
0.35µA typ.
0.95 to 6.5V
-40 to +105°C
1.2 to 5.2V (0.1Vstep)
±100ppm/°C typ.
10M
type.
Open drain, CMOS
Packages
SC-82ABB
SOT-25A
PLP-4A
Applications
1.
2.
3.
4.
The reset of CPU and MPU and logic circuit
Battery voltage check
Back-up circuit
Level detector
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
System Reset IC with delay PST89XA Series
Block Diagram
PST893Axxx Series
(Delay Resistance 10M type, CMOS Output)
VDD
RD
OUT
Vref
GND
CD
: Protection Circuit
PST894Axxx Series
(Delay Resistance 10M type, Open Drain Output)
VDD
RD
OUT
Vref
GND
CD
: Protection Circuit
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
System Reset IC with delay PST89XA Series
Pin Assignment
4
3
5
4
1
2
3
4
5
OUT
VDD
GND
NC
CD
1
2
1
2
3
4
GND
VDD
CD
OUT
1
2
3
SC-82ABB
(TOP VIEW)
SOT-25A
(TOP VIEW)
4
Heat
Spreader
Bottom
Note1
3
1
2
3
4
2
GND
OUT
CD
VDD
1
PLP-4A
(TOP VIEW)
Note1 : Heat Spreader Bottom with GND.
Pin Description
SC-82ABB
Pin No.
1
2
3
4
Pin name
GND
VDD
CD
OUT
GND Pin
VDD Pin / Voltage Detect Pin
Capacitor Connect Pin with Delay
Reset Signal Output Pin
Functions
SOT-25A
Pin No.
1
2
3
4
5
Pin name
OUT
VDD
GND
NC
CD
Functions
Reset Signal Output Pin
VDD Pin / Voltage Detect Pin
GND Pin
No Connection
Capacitor Connect Pin with Delay
PLP-4A
Pin No.
1
2
3
4
Pin name
GND
OUT
CD
VDD
GND Pin
Reset Signal Output Pin
Capacitor Connect Pin with Delay
VDD Pin / Voltage Detect Pin
Functions
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
System Reset IC with delay PST89XA Series
Absolute Maximum Ratings
Item
Supply Voltage
(Except where noted otherwise Ta=25°C)
Symbol
VDD max.
Ratings
- 0.3~+7.0
PST893 Series
GND- 0.3 ~
VDD max. +0.3
(CMOS Type)
GND- 0.3 ~ +7.0
(N-ch Open Drain Type)
20
20
GND- 0.3 ~ +VDD+0.3
150 (SC-82AB, SOT-25A)
400 (PLP-4A) (Note2)
- 40~+105
- 65~+150
mA
mA
V
mW
mW
°C
°C
Units
V
Output Voltage
OUT
PST894 Series
V
Input Current (V
DD
)
Output current (RESET, RESET)
CD Pin Input Voltage
Power dissipation
Operating temperature
Storage temperature
I
DD
I
OUT
V
CD
Pd
Topr
Tstg
Note2 : With PC board of glass epoxy.
Recommended Operating Conditions
Item
Operating Temperature
Supply Voltage
Symbol
Topr
V
DD
Ratings
- 40~+105
0.95~6.5
Units
°C
V
Model Name
P
S
T
8
9
a
a
Output Type
3
CMOS
Output
Open
drain
Output
b
c
CD pin charge Type Detecting Voltage Rank
A
delay
Resistance
120
V
TH
=1.20V
U
A
b
d
Package
SC-82ABB
R
c
d
e
e
Packing Specifications
R HOUSING
Halogen-contained Product
L HOUSING
Halogen-contained Product
R HOUSING
Halogen-free Product
L HOUSING
Halogen-free Product
4
N
SOT-25A
L
~
520
V
TH
=5.20V
~
R
PLP-4A
M
H
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
System Reset IC with delay PST89XA Series
Electrical Characteristics
Item
Symbol
(Except where noted otherwise Ta=25°C)
Rank
120
130
140
150
160
170
180
190
200
210
220
Min.
1.1880
1.1700
1.2870
1.2675
1.3860
1.3650
1.4850
1.4625
1.5840
1.5600
1.6830
1.6575
1.7820
1.7550
1.8810
1.8525
1.9800
1.9500
2.0790
2.0475
2.1780
2.1450
2.2770
2.2425
2.3760
2.3400
2.4750
2.4375
2.5740
2.5350
2.6730
2.6325
2.7720
2.7300
2.8710
2.8275
2.9700
2.9250
3.0690
3.0225
3.1680
3.1200
3.2670
3.2175
3.3660
3.3150
Typ.
1.2000
1.3000
1.4000
1.5000
1.6000
1.7000
1.8000
1.9000
2.0000
2.1000
2.2000
2.3000
2.4000
2.5000
2.6000
2.7000
2.8000
2.9000
3.0000
3.1000
3.2000
3.3000
3.4000
Max.
1.2120
1.2300
1.3130
1.3325
1.4140
1.4350
1.5150
1.5375
1.6160
1.6400
1.7170
1.7425
1.8180
1.8450
1.9190
1.9475
2.0200
2.0500
2.1210
2.1525
2.2220
2.2550
2.3230
2.3575
2.4240
2.4600
2.5250
2.5625
2.6260
2.6650
2.7270
2.7675
2.8280
2.8700
2.9290
2.9725
3.0300
3.0750
3.1310
3.1775
3.2320
3.2800
3.3330
3.3825
3.4340
3.4850
Units
Circuit
Measurement conditions
Reset threshold
V
TH
Ta=+25°C
Ta=−40~+85°C
230
240
250
260
270
280
290
300
310
320
330
340
V
2
Note3 : This device is tested at Ta=25°C, over temperature limits guaranteed by desigh only.
Note4 : The parameter is guaranteed by design.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
B628 Boost IC Peripheral Components and PCB Design Practice
PCB drawing board suggestions:As shown in the figure below, the red line from power input to output should be thick and wide. The inductor t...
In the registers of the PHY chip, you can set whether to add delay to the transmit and receive clocks, that is, RX Timing Delay mode and TX Timing Delay mode. When the rates are 1000Mbps and 10/100Mbp...
Why is there a reverse rotation process when the inverter starts the motor? The motor used is a 6kw forward and reverse running brushless DC motor, and the inverter is 7.5kw from Shenzhen Sine Electri...
[i=s] This post was last edited by dontium on 2015-1-23 11:46 [/i] The method of reducing bias error by introducing balancing resistors is taught by teachers in analog electronic technology class. But...
When compiling and simulating in QuartusII, a lot of warnings will appear, some of which can be ignored, while others need attention. Although you can get help about the warning by pressing F1, someti...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
LED Zone
京公网安备 11010802033920号
EEWORLD
