EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GC-07-1452-CC

Description
RES NET,THIN FILM,14.5K OHMS,100WV,.25% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GC-07-1452-CC Overview

RES NET,THIN FILM,14.5K OHMS,100WV,.25% +/-TOL,-25,25PPM TC,0303 CASE

WBA-T0303GC-07-1452-CC Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberWBA
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance14500 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBA
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
BulkUSB problem, urgent.
I would like to ask if there are any brothers who use the bulkusb that comes with DDK? After I compiled and installed it, it prompted an exclamation mark and could not be installed correctly. I don't ...
liyang203 Embedded System
SD card reading and writing problems
The pocket experiment platform of g2553 has a 2G TF card inserted. After downloading the official routine, the TF card cannot be read or written. (What does it mean when the routine says that only the...
zjw158 Microcontroller MCU
Can the eCAP function of TMS320C2801 capture the number of PWM pulses?
I checked the eCAP function manual and related samples of TMS320C2801, and they all introduce the measurement of pulse period using the capture function, but not the measurement of pulse number. Can t...
damofeishazcj Microcontroller MCU
RF power measurement system design completed
RF power measurement system, preliminary completionThe following are the source program, circuit diagram and PCB files.There are two versions of the program, one for 3.2-inch TFT driver ILI9320 and th...
lyzhangxiang ADI Reference Circuit
Congratulations to STM8S
Today, a user who bought EP868 abandoned MCP and switched to STM8S.I gave him the STM8S emulation function for free, but it seems that the customer didn't appreciate it.It seems that ST-Link is the pi...
ykyyky stm32/stm8
nucleo F411ER STlink and its built-in serial port problem
Problem 1: When I want to set breakpoints on the STlink that comes with the development board, I can't set them arbitrarily like jLINK. If I set more than a few, it won't work. It is not very convenie...
zf55029970 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 404  567  2555  2170  726  9  12  52  44  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号