EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCR-102-S-XXX-30-T-200-LT

Description
Board Connector, 2 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size170KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCR-102-S-XXX-30-T-200-LT Overview

Board Connector, 2 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle

BSTCR-102-S-XXX-30-T-200-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresLEAD LENGTH=1.230 INCH
body length0.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN LEAD (200) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
JESD-609 codee0
Manufacturer's serial numberBSTCR
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness200u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts2
To solve the problem of impedance continuity in PCB design, just read this article!
Everyone knows that impedance should be continuous. However, as Luo Yonghao said, "There are always times when you step on shit in life", and there are always times when impedance cannot be continuous...
ohahaha PCB Design
[Gizwits Gokit3 Review] Part 1: Some problems encountered during unboxing test
1. Introduction My application was not approved the first time, but I was quite excited when it was approved the second time. I wanted to test it immediately after getting the board, but the QR code o...
PowerWorld Domestic Chip Exchange
USB communication implementation based on StrongARM embedded Linux system.pdf
USB communication implementation based on StrongARM embedded Linux system.pdf...
yuandayuan6999 MCU
There is a circuit, I don't know why the effect is not very good, short circuit protection,
From EEWORLD cooperation group: 499581 Group owner: wangkjIt cannot be automatically turned on when powered on...
IC_faith PCB Design
Power-on issue with bq40z50-r1
For the BQ40Z50-R1 chip, first connect the analog power supply and burn the program. Then solder in the battery (single cell voltage is above 4V). Will the charge and discharge MOS be automatically tu...
hysdzgcsj2020 Analogue and Mixed Signal
Ask for help on a strange problem of stm8s105
After the program is downloaded, the device can run normally, but sometimes the device cannot work normally after a certain impact (such as falling to the ground or a large pulse interference) (the de...
honeycat205 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1244  977  1805  2368  520  26  20  37  48  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号