Resistor values are typically 120 to 240 ohms for 3.3V opera on and 82 to 120 ohms for 2.5V
opera on.
Figure 7 - Pull Up Pull Down Termina on
Resistor values are typically for 3.3V opera on
For 2.5V opera on, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous applica on notes on termina ng and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is op onal, depending on the applica on and the input logic requirements of
the next stage.
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
LVDS Applica on Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
+3.3V
OE or NC
10nF
1nF
1
6
10nF
OE or NC
2
5
100
3
4
10nF
OE or NC
2
5
Receiver
100
Receiver
3
4
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need addi onal components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
Since the official TCP server port is not available now, I found a server that can be used for testing: Tongxinmao - Online Application (tongxinmao.com)
1. Configuration parameters:After saving and ex...
We know that after 430 is powered on, the default DCO setting is RSELx = 7, DCOx = 3, MODx = 0, and its frequency range is 0.8~1.5MHz (3V voltage)
This raises a question, what is it exactly? There are...
In some special occasions, the microcontroller needs to be restarted (reset) to ensure that the functions of the product can be realized normally. Restart can be achieved through both hardware and sof...
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
1. The composition and structure of mobile phone lithium battery
Mobile phone lithium batteries are mainly composed of plastic shell upper and lower covers, lithium battery cells, protection c...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
Stepper motors, also called steppers, use the principles of electromagnetism to convert electrical energy into mechanical energy and have been used since the 1920s. With the increasing popularity o...[Details]
1 Causes of problems with electric vehicle batteries
1.1 Caused by the battery itself
Why do we say that? In the previous issue, we learned about the working princi...[Details]
Lithium iron phosphate batteries are used as lithium-ion secondary batteries. Their main application is now in power batteries, which have great advantages over NI-H and Ni-Cd batteries.
Lithi...[Details]
With the continuous development of integrated circuit technology, integrated circuits have developed from thousands of gates to the current level of millions and tens of millions of gates. The applica...[Details]
1. Introduction
Due to the good programmability and superior performance of FPGA, the number of embedded systems using FPGA chips in LCD splicing screens is increasing rapidly, especially in t...[Details]
Whether in mobile phones, high-end handheld instruments or embedded systems, 32-bit MCU ARM occupies an increasing share, and ARM has become the de facto industrial standard for high-end products...[Details]
Abstract Audio equalizer is one of the important tools for adjusting the timbre in audio system. This paper proposes a design of digital audio equalizer based on ADSP-BF533 hardware platform, and i...[Details]
Design Considerations
After the long-term deployment of smart meters (automatic meter reading infrastructure), a two-way communication will be established between the utility and the consumer. The ...[Details]
Overview
Modern
amplifier RF instruments
have impressive measurement capabilities and accuracy far exceeding their predecessors. However, these instruments cannot reach their full pote...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
