Thank you for having you +EEWORLD
Thank you eeworld for your company over the past year. It is great to have eeworld accompany me along the way. We have gained a lot of knowledge, broadened our horizo...
I'm new to 430 programming. What does the following statement do? It would be best if you could explain it in more detail. Thank you!do{IFG1 &= ~OFIFG;for (i = 0xFF; i > 0; i--);}while ((IFG1 & OFIFG)...
A friend posted a post in the analog circuit section of our forum. I feel that it cannot be seen by everyone there, because people who work on microcontrollers generally don't go there. So I reposted ...
[align=left][font=微软雅黑][size=4] [/size][/font][/align][align=left][font=微软雅黑][size=4]The annual Munich Shanghai Electronics Show has come to a successful conclusion. TE Connectivity showcased its late...
When using the signal compiler in dsp builder, the analyze was successful, but the synthesis had the following error: Error: Specified license does not contain information required to run the Quartus ...
Recruiting part-time UCOS II lecturers, weekends are available, practical project experience, more than two years of project experience, good expression skills are required. Interested parties please ...
UHF and HF are both general technology categories, but each category has independent supporting protocols. HF is more consistent in the 13.56MHz frequency band, although there are many internation...[Details]
In order to prevent traffic accidents, when the intelligent detection device of the car detects danger ahead, it must send a warning message to the driver. The voice alarm clearly reminds the drive...[Details]
This article discusses how to use an ultra-low-power RF transceiver chip from Zarlink Semiconductor for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices to achiev...[Details]
Maximize instrument utilization and reduce
test times
Increasing the throughput of automated test systems can improve efficiency. Using off-the-shelf tools (COTS) such as multicore proc...[Details]
The small size and low cost of home appliance control boards mean that high-cost materials will not be used in the circuit to solve the electromagnetic interference problem. The interference of hom...[Details]
Multiple Input and Multiple Output (MIMO) technology is arguably the next most important development in wireless communications since the advent of digital communications. Many new wireless commun...[Details]
There are many ways to attenuate signals. The most commonly used method is to divide the voltage using resistors. The common circuits are as follows:
Oscilloscope pre-stage attenuation c...[Details]
According to In-Stat/MDR, the number of mobile phones with Bluetooth capabilities will reach at least 300 million by 2005. One of the clear evidences of the increasing adoption of Bluetooth is that...[Details]
Most
embedded
systems are powered from a 48V backplane. This voltage is typically stepped down to a lower intermediate bus voltage of 24V, 12V, or 5V to power the circuit board racks withi...[Details]
Abstract: This paper introduces the controller, interface, display principle and driving method of the handheld computer LCD display based on the SA1110 microprocessor. Combined with the HPC projec...[Details]
This paper introduces the technology and application of optical transceiver modules and digital non-volatile variable resistors in optical communication networks, and focuses on the design and appl...[Details]
1. Introduction
Most of the existing heaters use traditional devices such as electric heating tubes and electric heating wires for heating. The outer shell of the electric heating tube is a ...[Details]
Femtocell base stations are required to meet stringent requirements in terms of interference, compatibility testing between mobile devices and networks (such as ad hoc networks, handovers), and mee...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, as more safety electronic devices, fuel consumption and fuel emission control electronic s...[Details]
Analysis of automotive sensor testing requirements
At present, the control system used in automobiles can be functionally divided into three parts: sensor unit, control unit and execution ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
