EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN1010H4990DBT0

Description
RESISTOR, THIN FILM, 0.5 W, 0.5 %, 50 ppm, 499 ohm, SURFACE MOUNT, 1010, CHIP
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

PTN1010H4990DBT0 Overview

RESISTOR, THIN FILM, 0.5 W, 0.5 %, 50 ppm, 499 ohm, SURFACE MOUNT, 1010, CHIP

PTN1010H4990DBT0 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
package instructionSMT, 1010
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length2.667 mm
Package formSMT
Package width2.54 mm
method of packingTR
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance499 Ω
Resistor typeFIXED RESISTOR
size code1010
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage150 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
EEWORLD University ----TI Precision Laboratory - Isolation
TI Precision Labs - Isolation : https://training.eeworld.com.cn/course/4869...
hi5 Analog electronics
Fighting back against India? It is said that Huawei will lay off 70% of its employees in India...
According to foreign media reports, multiple people familiar with the matter said that Huawei has lowered its 2020 revenue target in India by as much as 50% and plans to lay off 60% to 70% of its empl...
eric_wang Domestic Chip Exchange
How to set rules in AD so that the bottom-layer SMD components will not report errors after the top-layer direct plug-in.
How to set rules in AD so that the bottom-layer SMD components will not report errors after the top-layer SMD components are directly plugged in. For example, the SMD capacitors placed at the bottom-l...
hgc1145 PCB Design
LM3S811 learning experience 4--GPIO input program flow
Program flow for GPIO input:1) Clock initialization (set LDO output voltage, set system clock; 2) Enable the corresponding peripherals (GPIO); 3) Set the input and output type of each bit of the GPIO ...
qwertyuiop11111 Microcontroller MCU
MCU displays gif animation
I wonder if anyone has done a project to display a GIF animation on an LED screen. I'm planning to do this now, but I have no idea what to do. I have previously read BMP bitmap data from a PC and sent...
sgch Embedded System
My LED emergency light production process (1) Everyone else has received the prize, but I just started making it! Please watch the show later.
I just started making it after everyone else got their prizes! Please watch the show to come!I sorted and tested the components I bought! See the pictures![[i]This post was last edited by qwertyuiop11...
qwertyuiop11111 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1758  1859  593  1883  2660  36  38  12  54  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号