^For symbol “U” termination add .20 inches (0.51mm) to the positive length tolerance and .015 inches (0.38mm) to the positive width and thickness tolerances.
Ordering Information
03028
DSCC Drawing
Number
03028 (0603 case size)
BX
Dielectric
BR
BX
104
Capacitance
Code (pF)
2 Sig. Digits +
Number of
Zeros
Y
Voltage
W = 6.3V
X = 10V
Y = 16V
Z = 25V
A = 50V
B = 100V
C = 200V
J
Capacitance
Tolerance
J = ±5%
K = ±10%
M = ±20%
Z
End
Metallization^
U = SnPb (4% min)
Z = SnPb (4% min)
C
Group C
Testing Option
Blank = No group C testing
C = Full group C
L = 2,000 hour life test only
M = 1,000 hour life test only
H = Low voltage humidity only
7189
Packaging/Grade
(C-Spec)*
Blank = Waffle Pack
7189 = 7” Reel
^ “U” = Base metallization-barrier metal-solder coated (tin/lead alloy, with a min of 4% lead). Melting point is +200ºC or less. Metallization thickness is
≥
60μ-inches.
^ “Z” = Base metallization-barrier metal-tinned (tin/lead alloy, with a min of 4% lead).
* Additional reeling or packaging options may be available. Contact KEMET for details.
Additional termination options may be available. Contact KEMET for details.
In recent years, with the continuous improvement of control theory, research on fault diagnosis of control systems has attracted more and more attention [1][2], and many research results have been ach...
When keil5 software is simulating, I set a breakpoint in the main function, and then click run to try to jump to the breakpoint, but the following situation occursSet the breakpoint at the LED0=1 stat...
[i=s]This post was last edited by fish001 on 2018-6-21 21:40[/i] [size=5] One of the most important application areas of multi-core DSP is 3G digital mobile communication. This includes applications i...
1. Turn on voltage VT Turn-on voltage (also known as threshold voltage): the gate voltage required to start forming a conductive channel between the source S and the drain D; Standard N-channel MOS ...
This article is a repost. I think it is useful to everyone, so I transferred it to the forum:) There are many brands of power devices. Take MOSFET as an example. There are major brands in the world su...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
0 Introduction
Ultrasonic waves
are mechanical waves with a frequency of more than 20KHz, and the propagation speed in the air is about 340 m/s (at 20°C). Ultrasonic waves can be gene...[Details]
The automotive power electronics market has grown rapidly as comfort and active safety features become more common. As traditional mechanical functions shift to electronic applications, the demand ...[Details]
Designing low power circuits while achieving acceptable performance is a difficult task. Doing so in
the RF
bands increases the challenge dramatically. Today, nearly everything has wireless...[Details]
Today, automakers are integrating more and more complex electronic systems into cars. Allied Business Intelligence predicts that annual sales of the automotive semiconductor market will rise from $...[Details]
As we all know, the manufacturing of modern automobiles is divided into four major processes: stamping, welding, painting and assembly, and the powertrain constitutes five inseparable production pr...[Details]
Button cells (also called button cells) are those batteries with equal or larger diameter and height. The current size range of alkaline button cells is specified as follows: diameter 4.8mm-11.4mm,...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
