All specifications typical at TA=25℃, nominal input voltage and rated output current unless otherwise specified.Another 24V& 48V products, please inquire Our technical department!
"Hi Pot Test","Flash Tested","Withstand Voltage","Proof Voltage","Dielectric Withstand Voltage"&”Isolation Test Voltage" are all terms that relate to the same thing, a test voltage.
Applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Professional Power Module E_XS&F_XS series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 3KVDC for 1 minute.
A question commonly asked is,"What is the continuous voltage that can be applied across the part in normal operation?"
The E_XS&F_XS series has been recognized by Underwriters Laboratory for functional insulation.both input and output should normally be maintained within SELV limits i.e. Less
than 42.4V peak, or 60VDC.The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation
system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier, but then the circuitry on both sides of the
barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-amissible circuitry
according to safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials.
Construction and environment. We therefore strongly advise against repeated high voltage isolation testing. but if it is absolutely required, that the voltage be reduced by 20% from
specified test voltage.
This consideration equally applies to agency recognized parts for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation
system of physical spacing or barriers.
EFFICIENCY VS LOAD
2F05(XX)XS
2F12(XX)XS
2E05(XX)XS
2E12(XX)XS
CHARACTERISATION TEST METHODS
Ripple & Noise Characterization Method
Ripple and noise measurements are performed with the following test configuration.
C1
C2
C3
R1
R2
T1
RLOAD
1uF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10uF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter
with an ESR of less than 100mΩ at 100KHz
100nF multilayer ceramic capacitor, general purpose
450Ω resistor, carbon film,+/-1% tolerance
50Ω BNC termination
3T of the coxa cable through a ferrite toroid
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Measured values are multiplied by 10 to obtain the specified values.
# Compile and debug ESP32 program in VSCode * Take Win10 as an example, Linux is similar. * The debugger takes CMSIS-DAP v2 as an example. If you use the official FTDI or Jlink, the configuration will...
[i=s]This post was last edited by ena on 2016-1-6 15:09[/i] I have a 12V lithium battery in my hand now. When I wanted to charge it, it wouldn't charge. After I cut the seal and touched the circuit bo...
The 3M crystal oscillator circuit can start oscillating, but the output waveform amplitude (about 12V, the power supply is only 9V) is too large, what should I do? (Note: I have adjusted the matching ...
Compared with "Sate4412 Development Board Burning Tutorial V1.0.PDF", it adds the setting photos of the DIP switch to prevent some netizens from accidentally setting the wrong settings and causing the...
Recently I saw a kind of electric lamp that can be directly connected to the telephone line to draw electricity for lighting. Although it is not very bright, it seems to be a good night light.I have n...
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
Car lights, whether headlights, fog lights or tail lights, play an important role in driving safety. However, the material of the car lights determines that the probability of damage in a collision...[Details]
Features
POE technology can ensure the safety of existing structured cabling while ensuring the normal operation of the existing network and minimizing costs. The IEEE 802.3af standard is ...[Details]
1 Introduction
The stepper motor is an actuator of an open-loop servo motion system, which is controlled in a pulse mode and outputs angular displacement. Compared with AC servo motors and DC servo ...[Details]
If a car stereo could play multiple CDs, then such an in-car entertainment system was an advanced system configuration. Today's in-car infotainment systems are complex embedded subsystems that combine...[Details]
3. Driving circuit design
The power driver uses a field effect tube, which is a field-controlled device with a capacitance effect between the gate and source, so it has high requirements for t...[Details]
The coking workshop of Tianjin No. 2 Gas Plant is the core of the whole plant's production and an important source of economic and social benefits. Its production automation level and management an...[Details]
1. Composition of product standard system
LED is a new type of lighting appliance product. LED products include the LED itself, the supporting control devices and the lighting products that us...[Details]
For a long time, everyone has held a view when talking about power supplies: "Whether a power supply is good or not depends on whether it is heavy." So is it true that the heavier the power supply,...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
