KC24H-R series is a high-power LED driver design for the step-down constant current source. With high efficiency, wide input voltage range,
high-temperature environment, functional and so on. Contains a PWM dimming, analog dimming and remote shutdown capabilities.
They can be widely used in Backlight and 12V, 24V, 36V automotive lighting, landscape lighting, special lighting controls, commercial
lighting, street lighting, home lighting and other lighting systems.
Selection Guide
Input
Model
KC24H-300R(X1/X2/X3)
KC24H-350R(X1/X2/X3)
KC24H-500R(X1/X2/X3)
KC24H-600R(X1/X2/X3)
KC24H-700R(X1/X2/X3)
24(5.5-48)
Nominal
(range)
Input Voltage
(VDC)
Input Current (mA)
(Typ.)(5LEDs)
237
276
395
474
553
3.3-36
Output
Output Voltage
Output Current
(VDC)
(mA)
0-300
0-350
0-500
0-600
0-700
95
1000
Efficiency
(%, Typ),
Full Load
Max.
Capacitive
Load(uF)
Notes:
1. For the product model without a suffix such as KC24H-300R, this product is a 4-pin product without the functions of analogue dimming and PWM dimming.
2. For the product model with a suffix X1 such as KC24H-300RX1, this product is a 5-pin product only with the function of analogue dimming.
3. For the product model with a suffix X2 such as KC24H-300R X2, this product is a 5-pin product only with the function of PWM dimming.
4. For the product model with a suffix X3 such as KC24H-300R X3, this product is a 6-pin product with the functions of analogue dimming and PWM dimming.
Input Specifications
Item
Input Voltage Limit
Recommended Input Voltage
Min. Input-output Voltage Drop
Internal Power Dissipation
Reverse Polarity Input
Input Filter
Input voltage range
Vin=24V, 5LEDs
Operating Conditions
≤10
seconds
Min.
5
5.5
2
--
Typ.
--
24
--
--
Forbid
Capacitor Filter
Max.
55
46
4
0.7
W
VDC
Unit
Output Specifications
Item
Operating Conditions
Io:300mA
Io:350mA
Output Power
Io:500mA
Io:600mA
Io:700mA
Output Current Accuracy
Output Current Stability
Temperature Drift Coefficient
Ripple & Noise*
Over-temperature Protection
Output Short Circuit Protection
Io:300-600mA
Io:700mA
Vin=46V，Vo=3.3V~36V
-40
°C
~+71
°C
20MHz bandwidth(Vin=46V, 1~ 10 LEDs)
Min.
--
--
--
--
--
--
--
--
--
--
Typ.
--
--
--
--
--
±3
±5
±3
--
--
Max.
10.8
12.6
18
21.6
25.2
±5
±7
±5
± 0.015
100
Unit
W
%
%/
°
C
mVp-p
Self-recovery after cooling
Continuous, self-recovery
2014.02.28-A/3
Page 1 of 6
MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation
LED Driver
KC24H-R Series
Note: *Parallel line test method is adopted to test the ripple and noise. Test with X1 probe, please see
DC-DC Converter Application Notes
for specific
operation methods.
General Specifications
Item
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Case Temperature Rise
Lead Temperature
Operating Frequency*
MTBF
Thermal Impedance
MIL-HDBK-217F@25℃
Ta=25°C
Welding spot is 1.5mm away from the casing, 10 seconds
Operating Conditions
300mA / 350mA
500mA/ 600mA/ 700mA
Min.
-40
-40
-55
--
--
--
--
550
1000
--
Typ.
--
--
--
--
--
--
--
645
--
60
Max.
85
71
125
95
95
65
300
750
--
--
Unit
℃
%
℃
KHz
K hours
°
C
/W
Note:* When the mode works in the high-voltage input-area and 1LED load, its operating frequency will range from 100KHz to 400KHz.
PWM Dimming and Remote on/off Control
Item
Input Voltage Range
Analogue
Dimming
Output Current Range
Control Voltage Range
Driving Current
ON
PWM
Dimming&
Remote
Turn-off
OFF
Turn-off-mode Static Input Current
Isink
Isourse
PWM Dimming Frequency*
Note: *Refer to “PWM Dimming Control” on page five.
Operating Conditions
Vin=5.5-46V
Vin=5.5-46V
Full on
Full off
Vc=5V
Min.
Typ.
0-15V
Max.
0%-100%
0.2V±50mV
Unit
4.5V±200mV
--
--
Vc<0.6V
0.2
mA
Open or 2.8V<Vc<6V
Vin=24V, Vc <0.6V
Vc=5V, Vin=24V, 5LEDs
Vc<0.6V, Vin=24V, 5LEDs
--
--
--
--
400
--
1
--
--
1
--
200
μA
mA
μA
Hz
Physical
Specifications
Black flame-retardant and heat-resistant plastic (UL94-V0)
22.80*10.20*9.50 mm
4.3g(Typ)
Free air convection
Casing Material
Package Dimensions
Weight
Cooling method
EMC
EMI
Specifications
Conducted Disturbance
Radiated Emission
Electrostatic
Discharge
KC24H-xxxR(X1)
KC24H-xxxRX2/X3
EN55015
power port/CISPR22
CLASS B
CLASS B (see Fig. 5 for recommended circuit)
(see Fig. 5 for recommended circuit)
perf. Criteria B
perf. Criteria B
perf. Criteria A
perf. Criteria B
perf. Criteria B
perf. Criteria A
EN55015 /CISPR22
IEC/EN 61000-4-2
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
Contact ±6KV
Contact ±2KV(see Fig. 5 for recommended circuit)
10V/m
±1KV (see Fig. 5 for recommended circuit)
±1KV (see Fig. 5 for recommended circuit)
3Vr.ms
EMS
Radiation Immunity
EFT
Surge Immunity
Conducted Disturbance Immunity
2014.02.28-A/3
Page 2 of 6
MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation
LED Driver
KC24H-R Series
Product Characteristic Curve
Temperature Derating Curve
Output Current (mA)
500~700
300~350
300~350
-40
0
40
71 85
120
Operating Temperature(℃)
Fig. 1
Vin=12V
100
95
Efficiency(%)
KC24H-500R
Vin=24V
100
KC24H-700R
KC24H-500R
90
85
80
75
0
3
KC24H-700R
Efficiency(%)
KC24H-350R
90
KC24H-350R
80
70
Output Voltage(V)
6
9
12
3
6
9
12
15
18
21
Output voltage(V)
Vin=36V
100
KC24H-700R
KC24H-500R
Vin=48V
100
Efficiency(%)
KC24H-700R
90
Efficiency(%)
KC24H-350R
90
80
70
60
50
KC24H-500R
80
70
60
50
0
3
6
9
12
15
18 21 24 27
Output voltage(V)
30
33
36
KC24H-350R
3
6
9
12
15
18
21
24
27
30
33
36
Output voltage(V)
Design Reference
1. Input/output relationship
Input
voltage(VDC)
46
36
24
20
15
12
5.5
46
36
24
20
15
12
5.5
Output voltage
range(VDC)
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
Constant
Output power
output current
(W Max)
(mA)
300
300
300
300
300
300
300
500
500
500
500
500
500
500
10.80
9.60
6.30
5.10
3.96
3.00
1.20
18.00
16.00
10.50
8.50
6.60
5.00
2.00
Input
voltage(VDC)
46
36
24
20
15
12
5.5
46
36
24
20
15
12
5.5
Output
voltage
range(VDC)
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
Constant
output current
(mA)
350
350
350
350
350
350
350
600
600
600
600
600
600
600
Output power
(W Max)
12.60
11.20
7.35
5.95
4.62
3.50
1.40
21.60
19.20
12.60
10.20
7.92
6.00
2.40
2014.02.28-A/3
Page 3 of 6
MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation
LED Driver
KC24H-R Series
Constant
Output power
output current
(W Max)
(mA)
700
700
700
700
700
700
700
25.20
22.40
14.70
11.90
9.24
7.00
2.80
Output
voltage
range(VDC)
--
--
--
--
--
--
--
Constant
output current
(mA)
--
--
--
--
--
--
--
Input
voltage(VDC)
46
36
24
20
15
12
5.5
Output voltage
range(VDC)
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
Input
voltage(VDC)
--
--
--
--
--
--
--
Output power
(W Max)
--
--
--
--
--
--
--
2. Typical application circuit
( Analo gu e Dim )
(Ana lo gue Dim)
3
+Vin
GND
4
KC24 H-xxxRX 3
5
+Vout
6
-Vout 1st LE D
2
Last LE D
+Vin
4
3
5
+Vout
KC 24H-xxxRX 3
1
GND
1
6
-Vout
2
PTC
PTC
1st LED
Last LED
( PWM D im/ ON/ OFF)
(PWM Dim/ ON/ OFF)
Fig. 2 Application circuits in series
Fig. 3 Application circuits in series and parallel
If it is necessary to protect LED in actual application, you could connect a PTC to the input of every channel or all channels, as shown in
Figure 4.
Note: The negative output terminal can’t connect GND, or the module may be damaged.
3. Recommended AC input circuit
(Analogue Dim)
AC IN
D4
D1
Components
C1
C2
D1, D2, D3, D4
3
4
+
-
D3
5
+Vout
5VAC
~
32VAC
AC IN
C1
C2
KC24H-xxxRX3
1
2
+
D2
-
6
1st LED
Last LED
Specification
X1 Safety capacitor,
0.1μF /300VAC (QIYA)
100μF /63V Electrolytic capacitor,
Φ10×16(Flat
surface)NCC
Rectifier diode
1N4007 1A/1000V D0-41(PANJIT)
(PWM Dim/ON/OFF)
-Vout
Fig. 4
4. EMC solution-recommended circuit
L1
+Vin
Tvs
GND
①
C5
Last LED
Components
4
C3
DI M
*
R1
C6
Specification
SMC51A,1500W（ON）
CD53-82μH（CEAIYA）
470μF/100V（NCC）
225K/50V 1210 X7R (TORCH)
104K/50V 0805 X7R (TORCH)
105K/50V 1210 X7R (TORCH)
choose or no）
102K/2000V 1210 (TDK)（
470pF/100V 0805 (TORCH)
680Ω 0805(can replaced by
inductance or magnetic bead)
5 +Vout
Tvs
L1
1st LED
C1
C2
2
1
KC2 4H- xx xRX 3
C4
6 -Vout
C1
C2
C3
C4
C5
C6
R1
Fig.5 Recommended EMC circuit
Note: Add circuit
①
may let the ESD level of PWM-control pin reach to
±6KV.
2014.02.28-A/3
Page 4 of 6
MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation
LED Driver
KC24H-R Series
5. PWM dimming control
PWM Control Signal
1
0
Output Current
1
0
1
0
Output Current(LED turned on)
1
0
PWM Control Signal
1
0
Output Current(LED turned off)
PWM Control Signal
For PWM dimming signals with a certain frequency, the output current of the driver is related to the duty ratio of PWM signal. Refer to the
formula for the calculation method:
I
o_set
=
(DT-0.8)
Where, Io_set represents required output current (mA); D represents the duty ratio (%) of PWM signal; T represents the period (ms) of PWM
signal; and Io_norm represents the rated output value (mA) of the driver.
Note: The above formula is for reference only; and deviation of output current may exist due to various loads. The min. conducted time of PWM signal shall not
be less than 0.8ms, or the product will be in abnormal operation; in case of low voice from the driver during PWM dimming, it is normal since the PWM
dimming frequency is within the auditory frequency range of human ears (20Hz-20KHz in general). To prevent seeing flash of the LED by human eyes, it is
suggested to set the PWM dimming frequency between 100-200Hz.
[backcolor=rgb(239, 245, 249)]The company is in business, and is selling brand new AVR JTAGICE MKII emulator, MPLAB ICD2, MSP430 emulator. The price is negotiable. 13816546909[/backcolor]...
If the PWM output clock and pin configuration are written in external functions, such as rcc_configuration and gpio_configuration, and these two functions are executed before the PWM configuration fun...
I want to make a bitmap button. I use PictureBox, but it is very slow to handle click events. So I thought of inheriting from the Button class, but found that overriding OnPaint is invalid. The follow...
@soso @nmg@eric-wang@All administratorshttps://bbs.eeworld.com.cn/thread-507467-1-1.htmlIt's been three years so fast. After lunch in the afternoon, I specially greeted SOSO, and she asked me to "give...
[i=s] This post was last edited by paulhyde on 2014-9-15 09:20 [/i] Some simple assembly programs, I hope it can help friends who are just starting to learn assembly~~...
I have a question, that is, after the operating system is started, does it still access the hardware through the BIOS, or does the operating system completely take over the hardware and not go through...
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, this proportion may be as high as 30-40% as more safety electronics, fuel consumption and ...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
The serial interface real-time clock chip DS1302 launched by Dallas Company in the United States can trickle charge the backup battery of the clock chip. Due to the main features of the chip such a...[Details]
With the continuous advancement of various technologies in the field of measurement and control, the baseband subsystem of general measurement and control equipment has entered the fourth generation o...[Details]
Abstract: Based on the ZigBee parking lot SMS car search system, the location of the vehicle in the parking lot is sent to the owner through SMS, which is convenient for the owner to quickly find ...[Details]
At present, with the diversification of portable products and the almost harsh requirements for audio and video parts, the power consumption requirements of the whole machine have been raised to a ...[Details]
1 Battery technology determines the fate of energy vehicles
Regardless of whether new energy vehicles are hybrid or pure electric vehicles, they cannot do without the core technology of batter...[Details]
It should be understood as follows: DC-DC means direct current to direct current (conversion of different DC power values). Anything that meets this definition can be called a DC-DC converter, incl...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
