35mm DIN-rail package, hot plug, thickness: 22.5mm, Plastic UL94-V0
IP20(IEC60529 / EN60529)
About 128g
CONNECTION
In intrinsic safety explosion protection systems, isolating barrier belongs to affiliated device. It is installed at safe area, as a connection between
intrinsic safety devices in the hazardous area and non-intrinsic safety devices in the safe area. By limiting the energy to a certain safe am ount, it
ensures the safety of in spot devices and people.
Selection regulations for intrinsic safety explosion protection system:
1． The explosion protection grade of the barrier must be equal to or higher than that of in spot intrinsic safety explosion protection device.
2． Take inconsideration of hazardous end output resistance and loop resistance, ake sure the barrier’s output voltage meets the minimum operation
voltage requirement of in spot intrinsic safety device.
3． The safety parameters of Barrier’s intrinsic safety end meets:
Uo
≤
UI, Io
≤
Iin, Po
≤
Pin
Co
≥
Cin, Lo
≥
Lin
4． Select suitable Safety barrier which matches the in spot intrinsic safety device for the power’s phase, signal type and transmission mode.
5． Apply necessary protections, avoid influence the in spot intrinsic safety device’s operation from leakage current that generated by safety barrier.
Operation notes:
1.
2.
3.
4.
Please read the user manual carefully before using. If any questions please contact our technical support department.
Please do not use this product in hazardous area.
The power supply of this product should be 24VDC power source. It is forbidden to use 220VAC power supply.
To avoid invalid explosion protection function, or any failure, users disassemble this product is forbidden.
APPLICATION CIRCUIT DIAGRAM &
PIN DESCRIPTION
Hazardous area
Safe area
16
15
12
11
7
Channel1
8
3
DCS
Channel2
4
PLC
5
6
Power
Note:In single model channel2 is invaid
Transistor output mode and connections (safe area):
V CC
RL=2
½
20K
Ω
VCC
Passive pulse
Passive pulse
RL=2
½
20K
Ω
Transistor collector output
Transistor Emitter output
The copyright and authority for the interpretation of the products are reserved by
MORNSUN
TSX01-EX
2013.07.01-A/4
Page 2 of 3
INSTALLATION & DISASSEMBLY
Installation
DIN35mm standard rail installation:
1.Insert the top of the instrument card in the rail;
2.Push the bottom of the instrument into the rail.
Disassembly
1. Use a screwdriver (Width of edge
≤
6mm), cut in the metal card lock
from the underside;
2. Boost up the screwdriver and pry the metal card lock downwards;
3. Pull the instrument out of the rail.
3
1
2
PACKAGING DIMENSION & PACKAGING DIAGRAM
Note:
1. All specifications are measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
2. In this datasheet, all the test setup and methods are based on our corporate standards.
3. All characteristics are for listed models, and non-standard models may perform differently. Please contact our technical support for more details.
4. Please contact our technical support for any specific requirement.
5. Specifications of this product are subject to changes without prior notice.
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China.
Tel: 86-20-38601850
Fax:86-20-38601272
E-mail: info@mornsun.cn
Http://www.mornsun-power.com
The copyright and authority for the interpretation of the products are reserved by
[i=s]This post was last edited by zhaogong on 2017-6-19 03:09[/i] [align=left][font=宋体]It has been a long time since I received the board. I was too busy recently and didn't have much time to use it. ...
Hello, everyone! I am designing a communication cardrecently , using the 9054 chip . The 9054 chip works in J mode, and only needs to perform Target write and read operations. When I use the windriver...
[i=s]This post was last edited by Mandy on 2015-1-6 14:22[/i] [align=center][b]Design of a Wearable Holter Monitor Based on MSP430FR5969 (Full Version) [/b][/align] I am honored to apply for TI's Laun...
In the early 1990s, portable phones were all the rage. With the rapid development of electronic technology, today's mobile phones can not only send emails and text messages, but also take photos, ch...[Details]
1 Introduction
The multifunctional monitor is a commonly used clinical medical device. It can display the patient's electrocardiogram (ECG), respiration (RESP), blood oxygen saturation (SP...[Details]
introduction
At the beginning of this century, Veit used Einthoven's galvanometer to record the electrical activity of the human pregnant uterus from the body surface for the first time. In 19...[Details]
Introduction
The market for wireless telemetry products is developing rapidly. Recently, the industry has also set off a revolution in wireless applications. Wireless telemetry technol...[Details]
Due to the needs of medical development, in many cases, general thermometers can no longer meet the requirements of fast and accurate temperature measurement, such as measuring human body temperature ...[Details]
introduction
With the rapid development of my country's aviation industry, various new aircraft and control equipment have been successfully developed. Some previous measurement and control eq...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
This article first briefly introduces the working principles of current mode and voltage mode and their respective advantages and disadvantages; then discusses the ideal voltage mode using output c...[Details]
Broadband services supporting triple play voice, video and data are evolving for first mile customers (small businesses and homes). A key factor in this FTTx evolution is GPON (Gigabit Passive Opti...[Details]
Today's mobile phone production testing faces an increasingly complex environment, with challenges of multiple frequency bands and multiple standards, pressure on production test speed, and pres...[Details]
This article will discuss a common problem in wireless mobile data reception.
Problems facing RF receivers
The common problem faced by RF receivers is that the same hardware must be used ...[Details]
AD604 is a product of Analog Devices (AD). Compared with similar products, AD604 has the characteristics of ultra-low noise, high precision, continuously adjustable gain, and the decibel (dB...[Details]
introduction
With the increasing popularity of Internet applications, the degree of information sharing is constantly improving. The digitization and networking of embedded devices has b...[Details]
With the advent of the new economic era represented by the Internet, PCs have lost their former glory, and smart 3C products (Computer, Communication and Consumer) will set off a new wave. As one o...[Details]
The difference between CCD and CMOS sensors Mr.OH! briefly introduced CCD and CMOS in the second lecture, but for most students, what they see is a combination of integrated chips! The detailed int...[Details]
Switching Power Supply Study Group
京公网安备 11010802033920号
EEWORLD
