EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303GS-07-1353-BB

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 135000ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303GS-07-1353-BB Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 135000ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303GS-07-1353-BB Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802750338
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance135000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
Summary of bare metal program burning method for embedded Linux development board
1. Use imxdownload to burn (for nxp 6ULL development board) Copy imxdownload to the project root directory. We need to copy imxdownload to the project root directory, that is, in the same folder as le...
嵌入式enjoy Linux and Android
How to make a serial lottery button?
I wrote a lottery program. Now I can only use the keyboard to control the lottery and the prize drawing. But I want to make a thing with only one button, connected to the computer's serial port, and t...
梦幻泡影 Embedded System
How to set the resonant frequency of LLC
I just started learning LLC recently. In the design steps, I saw that I need to first determine the LLC resonant frequency, then determine the Q value, and finally get the parameters of the resonant n...
囚徒困境 Power technology
About 9b96 GPIO interrupt and interrupt vector table
9b96Each GPIO pin can be used as an external interrupt inputGPIOIntTypeSet(GPIO_PORTJ_BASE, GPIO_PIN_3, GPIO_LOW_LEVEL); //Set PJ3 as interrupt source, low level triggerGPIOPinIntEnable(GPIO_PORTJ_BAS...
jayce Microcontroller MCU
Design of reversing radar based on MSP430
With the increasing requirements for the intelligence of automobile assisted driving systems and the networking development of automobile electronic systems, the new reversing radar should be able to ...
火辣西米秀 Microcontroller MCU
Problems with creating a new platform with Platform Builder 4.2?
Hello everyone, I have a question for you! I installed platform Builder 4.2 by default, which only has the X86 model. When I create a new platform, the compilation platform cannot pass, and the follow...
jasonb Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1837  1029  1308  544  2379  37  21  27  11  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号