280X228S473B13 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> 280X228S473B13

280X228S473B13: DescriptionPotentiometer, Carbon Composition, 0.125W, 47000ohm, 500V, 20% +/-Tol, 7871; CategoryPassive components The resistor; File Size1MB，4 Pages; ManufacturerCTS; Environmental Compliance

Download Datasheet Parametric View All

280X228S473B13 Overview

Potentiometer, Carbon Composition, 0.125W, 47000ohm, 500V, 20% +/-Tol, 7871

280X228S473B13 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1205441117
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Rotary
Manufacturer's serial number	280(XB)
Package height	10.2 mm
Package length	19.7 mm
Package form	PCB Mount
Package width	18 mm
Rated power dissipation(P)	0.125 W
resistance	47000 Ω
Resistor type	POTENTIOMETER
rotation angle	300 deg
series	280(XB)
size code	7871
technology	CARBON COMPOSITION
Tolerance	20%
Operating Voltage	500 V

Preview

Download Datasheet

View All

Series 280

Commercial

Miniature

16mm Diameter

Composition

Variable Resistors

• Miniature 16mm style

• Bushing mounted with PC terminals and

shaft parallel or perpendicular to PC board

• Single or multiple section units

• Compatible with CTS 288 series rotary

encoders

Available with:

• Molded or metal shafts

• Push Pull Switch

• Electrical taps

• Center detent

Electrical and Mechanical Specifications

Resistance Range

500 ohms through 5 megohms (linear taper).

Resistance Tolerance

Standard: ±20%

Special tolerances available

Power Rating, Watts

watt per section through 10K ohms

watt per section above 10K ohms

Full rating @ 55°C derated to no load at 85°C

for linear tapers (derating required on

multiple section controls).

Voltage Rating

Bushings to Terminals:

High pot test, one minute — 750 VAC

Operating maximum

— 500 VDC

Across End Terminals:

350 VDC, load not to exceed power rating.

Insulation Resistance

100 megohms minimum dry

Angle of Rotation

Total Rotation:

Without switch — 300° ± 5°

Effective Rotation:

Without switch — 300° (approximate)

Rotation Torque

0.5-4 inch-ounces (36-288 gcm)

Switch Rating

Push pull type: 50mA, 20VDC

Technical Data Sheet 1448C

Technical Data Sheet 1280A

CTS CORPORATION /

MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS

Recommended Resources

Digital display electric meter/watt-hour meter circuit diagram using ADE7756

Intrinsically protected safety op amp

MOC3020 to MOC3023 type optocoupler/opto-isolator circuit

Q table schematic diagram

Multi-waveform signal generator made with 555

875p computer motherboard circuit diagram_006

RC charging calculation method: ==S 投票==E 投票 S 文章(这部分加style只是为了看效果,基本上表现都受编辑器设置控制)RC charging calculation method Reprinted from: http://hi.baidu.com/cumtsun/blog/item/b8ee5f16561cae4e20a4e93c.htmlExample 1 : As shown in the figure, ...; 安_然 Analog electronics

Relay drive problem. . Solution: Whether it is high or low, the relay will work. When it is high, the voltage difference between the 3rd and 4th pins of the optocoupler is 10V, and the relay is 24V. Shouldn't it be 0 when it is high?...; 浅夏 Analog electronics

WinCE Bluetooth problem solved thanks: Hello everyone, I have a few questions to ask you. I am studying the Bluetooth device of embedded system recently. The CPU used is s3c2443, and the OS is WinCE Platform Builder 5.0. I want to build a ...; hongfs Embedded System

How to put constant array in code segment in ARM?: Now I have a large constant array const int testdata[1000]. In order to save memory, I want to put it in the code segment. How do I declare it? In the past, in the microcontroller, the bytes were simp...; dzzl ARM Technology

HPS-to-FPGA access to FPGA I/O: The problem of HPS accessing the i/o port of FPGA through the HPS-to-FPGA bridge. It is not a lightweight bridge. Has anyone done it before? I have been working on it for two days, but it doesn't work...; Makefile FPGA/CPLD

The FPGA pin corresponding to the common IO signal on the PCB is the global clock: Dear heroes, the clock of the crystal oscillator is main_clk. After dividing the clock, we get the AD clock AD_clk. However, in the actual circuit diagram, I connected AD_clk to the pin corresponding ...; sunnian1234 FPGA/CPLD

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components