EEWORLDEEWORLDEEWORLD

Part Number

Search

IXD5122D629ER-G

Description
Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO6, USP-6
CategoryPower/power management    The power supply circuit   
File Size1MB,19 Pages
ManufacturerIXYS
Environmental Compliance
Download Datasheet Parametric View All

IXD5122D629ER-G Overview

Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO6, USP-6

IXD5122D629ER-G Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1969790744
package instructionHVSON,
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresDETECTION VOLTAGE IS 2.9V
Adjustable thresholdNO
Analog Integrated Circuits - Other TypesPOWER SUPPLY MANAGEMENT CIRCUIT
JESD-30 codeR-PDSO-N6
length2 mm
Number of channels1
Number of functions1
Number of terminals6
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeHVSON
Package shapeRECTANGULAR
Package formSMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Maximum seat height0.6 mm
Maximum supply voltage (Vsup)6 V
Minimum supply voltage (Vsup)1 V
Nominal supply voltage (Vsup)2 V
surface mountYES
technologyCMOS
Temperature levelINDUSTRIAL
Terminal formNO LEAD
Terminal pitch0.5 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
width1.8 mm
Product Specification
Product Specification
IXD5121/5122/5123/5124
Voltage Detector with ON/OFF Control of the Watchdog
FEATURES
Detect Voltage Range 1.6 V – 5.0 V in 0.1 V
increments
Accuracy ± 2%
Hysteresis 5% (typical)
Low Power Consumption
0.4 μA (Detect at V
IN
= 1.0 V)
0.6 µA (Release at V
IN
= 1.0 V)
Operating Voltage Range 1.0 V – 6.0 V
0
Detect Voltage Temperature Drift ±100 ppm/ C
Output Configuration - N-channel Open Drain
Watchdog with ON/OFF Control
Pre-programmed Release Time of 3.13, 50, 100,
200, and 400 ms
Pre-programmed Watchdog Time of 50, 100,
200, 400, 800, and 1600 ms
0
Operating Ambient Temperature - 40 + 85 C
Packages : USP-6C and SOT-25
EU RoHS Compliant, Pb Free
The series consists of a reference voltage source,
delay circuit, comparator, and output driver. With the
built-in delay circuit, this series does not require any
external components.
The
output is active LOW, when voltage below
V
DFL
is detected.
The EN (
pin controls the ON/OFF state of the
watchdog functions. This pin in an active state
disables the watchdog function, while the voltage
detector remains operational.
The IXD5122 and IXD5124 series have internal pull-
up/down resistors respectively that allows use these
IC with watchdog function active, while EN (
pins
are left open.
The detect voltages are internally fixed in the range
of 1.6 V to 5.0 V in 0.1 V increments.
Six watchdog timeout periods are available in a range
of 50 ms to 1.6 s.
Five release delay times are available in a range of
3.13 ms to 400 ms.
With low power consumption and high accuracy, the
series is suitable for precision mobile equipment.
The IXD5121/22/23/24 in ultra small packages are
ideally suited for high-density PC boards.
The IXD5121/22/23/24 is available in N-channel open
drain output configuration only.
These detectors are available in USP-6C and SOT-
25 packages.
APPLICATIONS
Microprocessor reset circuitry
Memory battery back-up circuits
Power-on reset circuits
Power failure detection
System battery life and charge voltage monitors
DESCRIPTION
The IXD5121/22/23/24 are highly precise, low power
consumption, CMOS voltage detectors with watchdog
function, manufactured using laser trimming
technology.
TYPICAL APPLICATION CIRCUIT
TYPICAL PERFORMANCE CHARACTERISTIC
Supply Current vs. Input Voltage
IXD5121 - 4
V
DF
= 2.7 V
IXD5121/22 Application Circuit (R
PL2
is used with IXD5121 only)
IXD5123/24 Application Circuit (R
PL2
is used with IXD5123 only)
PS037401-0615
PRELIMINARY
1
Q&A: What should you pay attention to when wiring FPGA?
Hello everyone: [b] I am laying out an FPGA board. Should I use four layers or two layers? I hope you can give me some advice. [/b] What are the requirements for the power line, clock line, and low li...
xunxun109 FPGA/CPLD
Guidelines for Quality C Programming
As the title says, it is very helpful for writing good code....
kernelpanic NXP MCU
How to select rectifier modules for communication power systems
There are many factors to consider when choosing a rectifier module for a communication power system. In the past, large monopolistic telecommunications companies often chose system solutions with a l...
zbz0529 Power technology
LPC800 development board circuit diagram
I downloaded the circuit diagram, but I don't understand how to connect the wires on the breadboard. Can an expert help me explain which of these rows of holes are already defined? Thank you....
hizzx NXP MCU
Rohde & Schwarz launches combined spectrum analyzer and phase noise tester
Rohde & Schwarz has released the company's first instrument specifically designed to measure phase noise and generate RF signal sources, the R&S FSUP. The instrument combines the company's many years ...
JasonYoo RF/Wirelessly
(Transferred) A composition written by a primary school student
Today, the teacher led us to visit the Martyrs Memorial Hall, which moved me deeply. Those revolutionary martyrs, for the sake of revolution, were not afraid of torture, bullets and rain, and sacrific...
shuangshumei Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1476  2919  1462  2241  1542  30  59  46  32  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号