EEWORLDEEWORLDEEWORLD

Part Number

Search

PGM26DR-G37

Description
Board Connector, 26 Contact(s), 2 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Receptacle,
CategoryThe connector    The connector   
File Size453KB,4 Pages
ManufacturerMueller Electric
Websitehttp://muellerelectric.com/
Download Datasheet Parametric View All

PGM26DR-G37 Overview

Board Connector, 26 Contact(s), 2 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Receptacle,

PGM26DR-G37 Parametric

Parameter NameAttribute value
Objectid4001282571
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.165 inch
subject depth0.157 inch
body length1.023 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage650VAC V
Insulation resistance5000000000 Ω
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial numberPGM
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature220 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
Plating thickness15u inch
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.118 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts26
How to determine the power or IPP of a TVS tube
The normal operating voltage VCC of the circuit is 24V, the current is 1A, the maximum operating voltage Vmax is 26V, and the maximum transient voltage that the subsequent circuit can withstand is 50V...
aq1261101415 Analog electronics
Using PWM to implement DA
I would like to ask if anyone has done this before? How should the peripheral circuit be implemented? Is it okay to use an op amp followed by an RC low-pass filter?...
哎呦害羞 NXP MCU
Looking for a video playback solution under WINCE
I need to play videos under WINCE, and I need to be able to play AVI and other files (video supports MEPG1\2\4, Divx, xVid formats, audio supports MP3, WAV, WAV). I don't know much about video playbac...
BITCH Embedded System
Help...an IC erasing problem
MC68HC711KS2 Does anyone know how to erase this IC after programming it? There is only one erse EEprom on the programmer, and this cannot erase all of it....
lixiyuan999 Embedded System
Recommend an App that can help debug BLE
[i=s]This post was last edited by cruelfox on 2017-7-18 16:14[/i] The NXP official Kinetis BLE Toolbox is good with the demo project of the development board, but it is not very useful if you want to ...
cruelfox NXP MCU
Half-bridge driver
Half-bridge drivers (also called high-side/low-side drivers) reduce switching losses, adapt to noisy environments, and improve system efficiency.Fundamentals of MOSFET and IGBT gate driver circuits Re...
Jacktang Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 821  2216  2456  1783  2533  17  45  50  36  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号