[align=left][color=#000]1. The 2407 program was developed on CCS2.2. Now the computer is installed with CCS3.3.83.20. When opening the project file, an error message "math.h file not found" is display...
(1) Install CCS3.3 software (2) Install the upgrade patch package CCS_v3.3_SR11_81.6.2.exe (3) Install the floating point support library setup_C28XFPU_CSP_v3[1].3.1207 (4) Install the programming plu...
Hardware resources: (1) One OURS-2410-F embedded development board: including 2410RP core board, 2410F baseboard and 4.3-inch LCD screen; (2) One DC 5V 3A DC power supply (supports AC 100~240V input) ...
2 Signal Description
2.1 Global Signals
Table 2-1 Global signalsSignalsourcedescribeACLKClock SourceGlobal clock signal. All signals are sampled on the rising edge of the global clock.ARESETnReset Sou...
China Energy Storage Network News:
On April 24, State Grid Corporation of China (hereinafter referred to as "SGCC") and China Southern Power Grid Co., Ltd. (hereinafter referred to as "CSGC")...[Details]
In the
AI
boom, the most talked about is
neural network
. However,
AI
is much more than that. Let's learn about the relevant content with the network communication editor.
...[Details]
When
artificial intelligence
can help humans take on some work, we always divide the responsibilities of both parties very clearly. When humans work, we rarely see
artificial intelligen...[Details]
On April 20, the Photovoltaic Summit, guided by Jiangsu Renewable Energy Industry Association, hosted by Growatt, and supported by LONGi Solar Technology Co., Ltd. and Jiangsu Bigo New Energy Group...[Details]
1. Usage scenarios In the first case, when using a common STM32 delay function, similar to HAL_Delay(time), since this function uses a loop to judge and delay, when executing this function, the ent...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
This is also a routine in the development board, with explanations of the key points. The program is as follows: /********************************************************* Program notes: First...[Details]
China Energy Storage Network News:
On the 7th, Jurong Economic Development Zone signed a strategic cooperation framework agreement on comprehensive energy services with State Grid Jiangsu Int...[Details]
As the weather gets colder, the way the north and south spend the winter has become a hot topic and people talk about it. Although the north is particularly cold, because there is heating, it can s...[Details]
This example sets up a button to adjust the square wave of different frequencies (multiples of 100) from 100-1000hz. In addition, serial port communication is added, and the corresponding frequency c...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
Manually assemble the following program machine code and analyze the execution function of the program segment. CLR A MOV R2, A MOV R7, #4 LOOP: CLR C MOV A, R0 RLC...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
The circuit shown in the figure requires that the light is off when the machine is turned on. Press the button once, and the light D1 will turn on and automatically turn off after a delay of 10 secon...[Details]
It is required to use timer/counter 1 for timing, with a timing of 1 second; timer/counter 0 for counter, and the external pulse to be counted is connected from P3.4 (T0). The microcontroller will co...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
