85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Standard Resistance Range
Linear Tapers (A, B, E, & H)......................................................................... (B & E) 1 K ohms to 1 megohm ................. (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) ................................................................ (D, G, S, & T) 1 K ohms to 1 megohm ....... (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance................................................................................. ±20 % or 10 %............................................ ±10 % or 5 %
Operating Temperature Range ........................................................................... -40 °C to +125 °C ....................................... -40 °C to +125 °C
Storage Temperature Range .............................................................................. -55 °C to +125 °C ....................................... -55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range .............................. ±1,000 ppm/°C ........................................... ±150 ppm/°C
Vibration (Single Section) ................................................................................... 15 G ........................................................... 15 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Shock (Single Section) ....................................................................................... 30 G ........................................................... 30 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Load Life ............................................................................................................. 1,000 hours ................................................ 1,000 hours
Total Resistance Shift .................................................................................. ±10 % maximum ........................................ ±5 % maximum
Rotational Life (No Load).................................................................................... 100,000 cycles ........................................... 100,000 cycles
Total Resistance Shift .................................................................................. (Linear taper) 10 ohms or .......................... (All tapers) ±5 % TRS maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift .................................................................................. (B & E tapers) ±10 % maximum ................ ±5 % maximum (all tapers)
Starting and Running Torque (Non-Locking Bushings)
Single Section..................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Dual Section ....................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Triple Section ...................................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Quadruple Section ...........................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Starting and Running Torque (Locking Bushings) ....................................................................................................................0.14 to 2.82 N-cm (0.2 to 4.0 oz.-in.)
Shaft Locking Torque with Locknut @ 10 in-lb. (B & E Bushings) .......................................................................................................................14 N-cm (20 oz-in.)
Mounting ...................................................................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ............................................................................................................................................................................................. 21 grams maximum
(Each Additional Section)...................................................................................................................................................................................... 6 grams maximum
Terminals ...........................................................................................................................................................................................Printed circuit terminals or J-Hooks
Soldering Condition .................................................................................. Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ...........................................................................................Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number
Ganging (multiple section potentiometers) ...................................................................................................................................................................... 4 cup maximum
Hardware ...............One lockwasher and one mounting nut is shipped with each potentiometer; locking bushing versions are shipped with one additional locking nut
For dimensional drawings see pages 3 & 4. For ordering information see page 5.
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Initial Electrical Characteristics
1
Conductive Plastic Element
Cermet Element
Environmental Characteristics
1
Mechanical Characteristics
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
*RoHS Directive 2015/863, Mar 31, 2015 and Annex.
Specifications are subject to change without notice. Users should verify actual device performance in their specific
applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the
last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
81/82 – 5/8 ˝ Square Single-Turn Panel Control
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifications
Initial Electrical Characteristics
1
Contacts:
DPST ............................................................................................................................................................................. N.O/N.O.,N.C./N.C. or N.O./N.C.
Power Rating (Resistive Load):
DPST ..........................................................................................................2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz
Operating Temperature Range ...................................................................................................................................................................... -40 °C to +70 °C
Storage Temperature Range ....................................................................................................................................................................... -65 °C to +125 °C
Vibration (Dual Section)......................................................................................................................................................................................................8 G
(Triple Section) ..................................................................................................................................................................................................5 G
(Quadruple Section) ..........................................................................................................................................................................................3 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Shock (Dual Section) ........................................................................................................................................................................................................20 G
(Triple Section) ....................................................................................................................................................................................................15 G
(Quadruple Section) ............................................................................................................................................................................................10 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Switch Actuating Torque (50% Duty cycle @ Rated Power Load) .................................................................................1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance .....................................................................................................................................................................100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Contact Resistance (0.1 VDC-10 mA) ..........................................................................................................................................10 milliohms maximum
Switch Housing Material ................................................................................................................. High temperature, flame retardant, thermosetting plastic
Mechanical Characteristics
1
Actuating Torque (Each Section, Switch Module Only) ......................................................................................................3.53 to 10.6 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly) ....................................................................................................0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)
Detent ....................................................................................................................................................................................................CW or CCW standard
Contact Materials......................................................................................................................................................................... Fine silver with gold overlay
Terminal Styles .................................................................................................................................................................................................Solder lug only
Standard Orientation .............................................................................................................................................................In-line with control terminals
Optional .........................................................................................................................................................................Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) ........................................................................................................ 0.9 Kg (2 lbs.) minimum
1
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Terminal outlines shown as solid lines represent PC Pins, available
on Model 81. Dashed line terminal outline represents "J" Hook,
available on Model 82.
5.97 ± .38
(.235 ± .015)
5.08 ± .38
(.200 ± .015)
12.7
(.50)
5.33 ± .76
(.210 ± .03)
10.16 ± .13
(.400 ± .005)
Note: For units with dual concentric shaft styles, a
2.54 (.100) spacer is added between the module(s) driven
by the outer shaft and those driven by the inner shaft.
For G, K, or V shafts, add the spacer between
modules 1 and 2. For L or M shafts, add the spacer
between modules 2 and 3. For N or P shafts, add the
spacer between modules 3 and 4.
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
DIMENSIONS:
MM
(INCHES)
Suggested Panel Layout
B
C
BUSHING
A, B & J
E
DIM A
9.91
(.39)
ANTI-ROTATION LUG
A
B
C
E
F
J
K
DIM B
7.75
(.305)
7.75
(.305)
N/A
13.49
(.531)
N/A
9.53
(.375)
9.53
(.375)
DIM C
N/A
7.75
(.305)
7.75
(.305)
N/A
N/A
N/A
9.53
(.375)
DIM D
N/A
N/A
N/A
N/A
7.75
(.305)
N/A
N/A
DIM E
2.49
(.098)
2.49
(.098)
2.49
(.098)
3.45
(.136)
2.54
(.100)
2.54
(.100)
2.54
(.100)
D
A
C, E & N
R&S
U
6.73
(.265)
10.5
(.413)
7.5
(.295)
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Product Dimensions
Primary Potentiometer Module
Model 85/86
14.53
(.572)
9.58 ± .38
(.377 ± .015)
Secondary Potentiometer Module
Model 85/86
10.16
(.400)
15.88
(.625)
15.88
(.625)
Shaft Flat Orientation*
120 ° ± 5 ° CCW END
30 ° ± 5 °
12.7
(.50)
5.97
(.235)
8.56
(.337)
1.60
(.063)
FLATTED SHAFT
5.08
(.200)
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
5.08
(.200) 8.56
(.337)
5.08
(.200)
Switch Module
Model 85/86
REAR
PLATE
COVER
2.77
(.109)
1.35
(.053)
2.29
(.090)
TYP.
6 PLACES
Assembly Sequence
Model 85/86
Secondary Potentiometer Module
Switch Module Terminal Orientation
3
1
4
2
3
1
18.42
(.725)
2.41
1.14
(.095)L X (.045)W
SLOT TYP. 6 PLACES
4
2
HORIZONTAL ORIENTATION
(Types R56, R57, R58 & R59)
VERTICAL ORIENTATION
(Types R50, R51, R52 & R53)
2.92
(.115)
9.53
(.375)
REAR
COVER
PLATE
SWITCH
MODULE
PRIMARY
POTENTIOMETER
MODULE
4
2
3
1
3
1
4
2
DPST (NO/NC)
(TYPES 50, 51, 56, 57)
DPST (NO/NO)
(TYPES 52, 53, 58, 59)
Switch contacts shown in detent position.
Locating Lug Options - All Model 80 Series
A
.46
(.018)
7.75
(.305)
E
13.49
(.531)
J
9.53
(.375)
.79 ± .41
(.031 ± .016)
E = 2.36 ± .76
(.093 ± .03)
H & J = 1.98 ± .41
(.078 ± .016)
2.31
(.091)
3.18
(.125)
.46
(.018)
2.36
(.093)
7.75
(.305)
A
C
7.75
(.305)
.46
(.018)
.79 ± .41
(.031 ± .016)
MOUNTING
SURFACE
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
RECOMMENDED
PANEL LAYOUT
7.75
#40 DRILL
(.305)
2.49
DIA.
(.098)
9.91
DIA.
(.390)
.127
(.005)
.XX ± .38
(.015)
ANGLE ± 5 %
2.31
(.091)
DIMENSIONS:
MM
(INCHES)
NOTE: "D" OPTION - NO A/R LUG. OTHER LOCATING LUG OPTIONS AVAILABLE. CONSULT FACTORY FOR DETAILS.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
[i=s] This post was last edited by qwqwqw2088 on 2015-2-11 15:43 [/i] 1. What are the characteristics of electronic devices made of semiconductor materials compared with traditional vacuum electronic ...
I recently received a 32*64 two-color dot matrix screen composed of 595 and 138, but it just won’t light up. This is my first time using this thing. I checked a lot of information, but I just can’t un...
1. IIC DescriptionThe above figure shows that there should be at least one microcontroller in the IIC bus topology. The controller communicates with other associated devices through the SCL and SDA li...
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
Inverter power supplies on the market can generally be divided into two categories: sine wave inverters and square wave inverters. Some engineers also like to categorize pure sine wave inverters as...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
On August 18th, China's largest expressway
charging station,
the G25 Changshen Expressway Tonglu Service Area (South Area), officially opened and launched its integrated solar-storage-charg...[Details]
Lithium-ion batteries are a key component of electric vehicles. Their high energy density enables them to store a large amount of energy in a relatively compact and lightweight package, which is cr...[Details]
When we pick up an unfamiliar object, the first thing we want to know is what it actually does. A drive shaft, as the name suggests, is a shaft that transmits power. It's the transmission medium th...[Details]
As in-vehicle audio and video entertainment features become increasingly diverse, the demand for digital transmission of audio and video information is urgent. Traditional protocols such as IEEE 13...[Details]
With the global number of new energy vehicles expected to exceed 45 million by 2025, the performance boundaries of battery management systems are being reshaped.
Infineon Technologies
'
...[Details]
According to the latest financial report data, thanks to its leading position in advanced technology, TSMC's profit performance in the second quarter of 2025 was extremely impressive, with net prof...[Details]
Relying on Zena CSS and Arm's complete partner ecosystem, we will accelerate the implementation of autonomous driving.
Close your eyes and imagine yourself getting into your car, rea...[Details]
Shock absorbers, as the name implies, are responsible for cushioning and absorbing shocks in a car. So how much do you know about shock absorbers and how to replace them in electric cars?
...[Details]
introduction
With the continuous development of electronic technology and the continuous upgrading of medical equipment, the demand for medical liquid infusion precision is becoming increasing...[Details]
introduction
As the concept of "low-carbon travel and green environmental protection" becomes more and more popular, bicycles have become a crucial means of transportation. Currently, urban pu...[Details]
The working principle of a frequency converter is to process input fixed-frequency AC power through circuits such as rectification, filtering, and inversion, and then output AC power with variable ...[Details]
Today, we'll discuss why contactors shouldn't be connected to the output terminals of VFDs. This is because if the contactor at the VFD output isn't engaged, it will only engage when the VFD starts...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
