IEC Inlet Filters
FN 9222
General Performance IEC Inlet Filter
n
n
n
n
n
n
Rated currents up to 20A
Excellent performance/size ratio
Optional medical versions (B type)
according to IEC/EN 60601-1
Snap-in versions (S and S1 type)
Hot inlet versions (HI type)
Optional overvoltage protection
(Z type)
Approvals
except HI-types
Technical specifications
Maximum continuous operating voltage:
Operating frequency:
Rated currents:
Approvals by rated current:
250VAC, 50/60Hz
dc to 400Hz
1 to 20A @ 50°C
1 to 10A (ENEC, CQC)
16A (ENEC, CQC) for 16 and 20A types
1 to 20A (UL, CSA)
P –> PE 2000VAC for 2 sec (standard types)
P –> PE 2500VAC for 2 sec (B types)
P –> N 1000VAC for 2 sec (1 to 10A types, not Z types)
P –> N 250VAC for 2 sec (all Z types)
P –> N 1100VDC for 2 sec (16 and 20A types, not Z types)
IP40 according to IEC 60529
-25°C to +85°C (25/85/21)
UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939
(X to XX A, not Z types)
UL 94V-2 or better
2kV, IEC 61000-4-5
≤15A: 3,040,000 hours
≥16A: 2,256,000 hours
Typical electrical schematic
Standard, R and B types
Cx
N
PE
P
Line
Load
R
2xL
2xCy
N‘
PE
P‘
High potential test voltage:
Z types
Cx
N
PE
P
Line
Load
2xL
2xCy
N‘
PE
P‘
Protection category:
Temperature range (operation and storage):
Design corresponding to:
Flammability corresponding to:
Surge pulse protection (optional):
MTBF @ 40°C/230V (Mil-HB-217F):
Features and benefits
The FN 9222 IEC inlet filter combines an
IEC inlet and mains filter with excellent filter
attenuation in a small form factor. Choosing
the FN 9222 product line brings you the rapid
availability of a standard filter associated with
the necessary safety acceptances. Standard
IEC connector filters are a practical solution
helping you to pass EMI system approval in
a short time. A wide selection on amperage
ratings, output connections, mounting
possibilities and filters for medical applications
are designed to offer you the desired solution.
n
n
n
n
n
n
n
Typical applications
n
Exceptional conducted attenuation
performance, based on chokes with high
saturation resistance and excellent thermal
behavior.
Rear/front or snap-in mounting.
Wide mounting flanges available.
Optional medical versions (B type) comply
with the requirements of IEC/EN 60601-1
for creepage and clearance, leakage
current and high potential testing.
12 and 15A types with hot inlet available.
Optional surge pulse protection.
Different output connections offering
maximum flexibility for assembly.
Portable electrical and electronic
equipment
n
Small to medium-sized machines and
household equipment
n
Single-phase power supplies, switch-mode
power supplies
n
n
n
Test and measurement equipment
Medical equipment
Rack mounting equipment
n
Custom-specific versions are available on
request.
> Components
> FN 9222
Product selector
FN 9222xx-yy-..HI-zz
Snap-in range for S version only
Blank:
20:
Snap-in range 0.7 to 1.5mm
Snap-in range 1.5 to 2.2mm
Blank:
HI:
Standard IEC inlet type C14 (1 to 15A types), C20 (16 and 20A types)
Hot IEC inlet type C16 (12 and 15A types only)
06:
07:
Faston 6.3 x 0.8mm (spade/soldering)
Wire leads
1 to 20:
Rated current
Blank:
R:
B:
Z:
Standard version
Bleed resistor
Medical version (with bleed resistor and without Y2-capacitor)
Optional surge pulse protection with additional varistor (MOV)
(Z types have longer housings, only available for FN 9222UZ-yy-06)
Blank:
U:
S:
S1:
Standard housing with mounting flanges
Housing with wider mounting flanges
Snap-in version, snapper on vertical side (1 to 15A types only)
Snap-in version, snapper on horizontal side (1 to 15A types only)
For example: FN 9222-15-07, FN 9222S1B-10-06-20, FN 9222R-12-06HI, FN 9222UZ-15-06
Typical filter attenuation
Per CISPR 17; A = 50Ω/50Ω sym; B = 50Ω/50Ω asym; C = 0.1Ω/100Ω sym; D = 100Ω/0.1Ω sym
1 and 3A types
6 to 10A types
12 and 15A types
16 and 20A types
Mobile and portable
京公网安备 11010802033920号
EEWORLD
