The TRPC03-E1G SFP series of fiber optic transceivers w ith
integrated digital diagnostics monitoring functionality provide
a quick and reliable interface for short reach ( ,intermediate
SR)
reach ( and long reach (
IR)
LR) applications. The diagnostic
functions,alarm and w arning features as described in the Multi-
Source A greement (
MSA ) document, SFF-8472 (
Rev. 9.4) are
,
2
provided via an I C serial interface.
Available products under this series are compliant w ith
applicable SON ET/SD H standards for OC-3/STM-1. A ll modules
satisfy Class I Laser Safety requirements in accordance w ith the
U .S. FD A /CD RH and international IEC-60825 standards.
The TRPC03-E1G transceivers connect to standard 20-pad
SFP connectors for hot plug capability. This allow s the system
designer to make configuration changes or maintenance by
simply plugging in different types of transceivers w ithout
removing the pow er supply from the host system.
The transceivers have colored bail-type latches,w hich offer an
easy and convenient w ay to release the modules. The latch is
compliant w ith the SFP MSA .
The transmitter design incorporates a highly reliable 1310nm
InG aA sP laser and a driver circuit. The receiver features a
transimpedance amplifier IC optimized for high sensitivity
and w ide dynamic range. The transmitter and receiver D ATA
interfaces are AC-coupled internally. LVTTL Transmitter D isable
control input and Loss of Signal output interfaces are also
provided.
The transceivers operate from a single +3.3V pow er supply over
tw o operating case temperature ranges of -5°C to +70°C (
COM)
,
or -40°C to +85°C ( D ) The housing is made of metal for EMI
IN .
immunity.
F ea tu res
þ
Compatible w ith SFP MSA
þ
Compliant w ith SON ET/SD H OC-3/STM-1 (
155Mb/s)
þ
Lead Free D esign & Fully RoH S Compliant
þ
SON ET/SD H Reaches (
SR-1,IR-1 & LR-1)
þ
D igital D iagnostics through Serial Interface
þ
Internal Calibration for D igital D iagnostics
þ
Eye Safe (
Class I Laser Safety)
þ
D uplex LC Optical Interface
þ
-40°C to +85°C Operating Case Temperature Option
þ
Excellent EMI & ESD Protection
þ
H ot-pluggable
þ
TX Fault & Loss of Signal Outputs
þ
TX D isable Input
þ
Single +3.3V Pow er Supply
A bsolute Maximum R atings
Parameter
Storage Temperature
Operating Case Temperature
1
Supply Voltage
Input Voltage
1
Symbol
T
st
Commercial
Industrial
T
op
V
cc
V
in
Minimum
- 40
-5
- 40
0
0
Maximum
+ 85
+ 70
+ 85
+ 5.0
V
cc
Units
°C
°C
V
V
Measured on top side of SFP module at the front center vent hole of the cage.
An Oplink Company
S0115,Rev.02
2010-12-23
TR PC0 3-E 1G Single Mode
Transmitter Perf
ormance C haracteristics
(Over Operating Case Temperature,
V
CC
= 3.13 to 3.47V)
All parameters guaranteed only at typical data rate
Parameter
Operating D ata Rate
1
Average Optical Output Pow er
(
coupled into single mode ber)
,
50% duty cycle
Extinction Ratio
Center W avelength
Spectral W idth (
RMS)
Optical Output Eye
1
Symbol
B
IR-1
LR-1
IR-1
LR-1
IR-1 & LR-1
!
c
Minimum
-
- 15.0
- 5.0
10
1261
1270
-
Typical
156
- 11.0
- 3.0
-
1310
1310
-
Maximum
-
- 8.0
0
-
1360
1360
3
Units
Mb/s
dBm
dB
nm
nm
P
O
P
hi
/
l
P
o
RM S
Compliant w ith Telcordia G R-253-CORE and ITU -T Recommendation G .957
D ata rate ranges from 50Mb/s to 266Mb/s. H ow ever,some degradation may be incurred in overall performance.
R eceiver Perf
ormance C haracteristics
(Over Operating Case Temperature,
V
CC
= 3.13 to 3.47V)
All parameters guaranteed only at typical data rate
Parameter
Operating D ata Rate
1
2
Receiver Sensitivity (
-10
BER)
10
2
Maximum Input Optical Pow er (
-10
BER)
10
Symbol
B
P
min
P
ma
x
P
l
os+
P
l
os-
t_oss_ #
l o"
t_oss_
l on
-
-
Minimum
-
- 34.0
- 7.0
-
- 45.0
-
2.3
0.5
1100
-
Typical
156
- 36.0
0
-
-
-
-
1.5
-
-
Maximum
-
-
-
- 34.0
-
100
100
-
1600
- 25.0
Units
Mb/s
dBm
dBm
dBm
µs
dB
nm
dB
LOS Thresholds
LOS Timing D elay
LOS H ysteresis
W avelength of Operation
Receiver Re ectance (
LR-2 only)
1
2
Increasing Light Input
D ecreasing Light Input
Increasing Light Input
D ecreasing Light Input
D ata rate ranges from 50Mb/s to 266Mb/s. H ow ever,some degradation may be incurred in overall performance.
Specified in average optical input pow er and measured w ith 2
23
-1 PRBS at 156Mb/s and 1310nm for IR-1& LR-1.
Laser Saf
ety
Laser Safety:
A l t
l ranscei
vers are C l I Laser product
ass
s
per FD A / D R H and IEC -
C
60825 st
andards.They m ust be
operat under speci ed operat ng condi i
ed
!
i
t ons.
Oplink Communications, Inc.
D ATE OF MA N U FACTU RE:
This product complies w ith
21 CFR 1040.10 and 1040.11
Meets Class I Laser Safety Requirements
Oplink Communications,
I
nc.
2
S0115,Rev.02
2010-12-23
TR PC0 3-E 1G Single Mode
Transmitter Electrical I
nterf
ace
(Over Operating Case Temperature,
V
CC
= 3.13 to 3.47V)
Parameter
1
Input Voltage Sw ing (TD + & TD -)
2
Input H IG H Voltage (TX D isable)
2
Input LOW Voltage (TX D isable)
3
Output H IG H Voltage (TX Fault)
3
Output LOW Voltage (TX Fault)
1
Symbol
V
PP-DIF
V
IH
V
IL
V
OH
V
OL
Minimum
0.35
2.0
0
2.0
0
Typical
-
-
-
-
-
Maximum
2.4
V
CC
0.8
V
CC#
0.3
+
0.8
Units
V
V
V
V
V
D i erential peak-to-peak voltage.
There is an internal 4.7 to 10k pull-up resistor to
VccT.
3
Open collector compatible,4.7 to 10k pull-up resistor to
Vcc
( ost Supply Voltage)
H
.
2
R eceiver Electrical I
nterf
ace
(Over Operating Case Temperature,
V
CC
= 3.13 to 3.47V)
Parameter
1
Output Voltage Sw ing ( + & RD -)
RD
2
Output H IG H Voltage (
LOS)
2
Output LOW Voltage (
LOS)
1
2
Symbol
V
PP-DIF
V
OH
V
OL
Minimum
0.6
2.0
0
Typical
-
-
-
Maximum
2.0
V
CC#
0.3
+
0.5
Units
V
V
V
D i erential peak-to-peak voltage across external 100 load.
Open collector compatible,4.7 to 10k pull-up resistor to
Vcc
( ost Supply Voltage)
H
.
Electrical Pow er Supply C haracteristics
(Over Operating Case Temperature,
V
CC
= 3.13 to 3.47V)
Parameter
Supply Voltage
Supply Current
OC-3 (
IR-1,LR-1)
Symbol
V
CC
I
CC
Minimum
3.13
-
Typical
3.3
190
Maximum
3.47
270
Units
V
mA
Module D ef
inition
MO D _D EF(0)
pin 6
TTL LOW
MO D _D EF(1)
pin 5
SCL
MO D _D EF(2)
pin 4
SD A
I
nterpretation by H ost
Serial module definition protocol
Electrical Pad Layout
20
19
18
17
16
15
14
13
12
11
TX G N D
TD - (TX D ATA IN -)
TD + (TX D ATA IN +)
TX G N D
VccTX
VccRX
RX G N D
RD + ( D ATA OU T+)
RX
RD - ( D ATA OU T-)
RX
RX G N D
H ost B oard C onnector Pad Layout
20
19
18
17
16
15
14
13
12
11
Tow ard
A SI
C
1
2
3
4
5
6
7
8
9
10
TX G N D
TX Fault
TX D isable
MOD _D EF(
2)
MOD _D EF(
1)
MOD _D EF(
0)
N O CON N ECTION
LOS
RX G N D
RX G N D
1
2
3
Tow ard
B ezel
4
5
6
7
8
9
10
Top of Board
Bottom of Board
(as viewed thru top of board)
Oplink Communications,
I
nc.
3
S0115,Rev.02
2010-12-23
TR PC0 3-E 1G Single Mode
Example of SFP host board schematic
1
m
H c l f rt bead
oior eri
e
( 2
W
s isr it nc
<0.
ere essa e)
Vc
c
3.
3V
Vc
c
3.
3V
+
10
0.
1
0.
1
16
R R R
2
8
4
TRPC0 - G
5
3 E1
6
50
W
l
i
ne
13
50
W
l
i
ne
12
R
R
TX Faul
t
LOS
MOD_DEF(
2)
MOD_DEF(
1)
MOD_DEF(
0)
RX DATA OUT+
to 50
W
load
RX DATA OUT-
to 50
W
load
+
15
10
0.
1
TX Diabl
s e
50
W
l
i
ne
TX DATA IN+
50
W
l
i
ne
TX DATA IN-
3
18
19
1,9, 11, 17,
10, 14, 20
R:4.7 to 10k
CA P Values in
µF
A pplication N otes
Electrical Interface:
A ll signal interfaces are compliant w ith
the SFP MSA specification. The high speed D ATA interface is
differential AC-coupled internally w ith 1 F and can be directly
connected to a 3.3V SERD ES IC. A ll low speed control and sense
output signals are open collector TTL compatible and should
be pulled up w ith a 4.7 - 10k resistor on the host board.
Loss of Signal (LOS):
The Loss of Signal circuit monitors the
level of the incoming optical signal and generates a logic H IG H
w hen an insufficient photocurrent is produced.
TX Fault:
The output indicates LOW w hen the transmitter
is operating normally,and H IG H w ith a laser fault including
laser end-of-life. TX Fault is an open collector/drain output
and should be pulled up w ith a 4.7 - 10k resistor on the host
board. TX Fault is non-latching (
automatically deasserts w hen
fault goes aw ay)
.
TX Disable:
W hen the TX D isable pin is at logic H IG H , the
transmitter optical output is disabled (
less than -45dBm)
.
Serial Identification and Monitoring:
The module definition
of SFP is indicated by the three module definition pins,
MOD _D EF( ,MOD _D EF( and MOD _D EF( . U pon pow er up,
0)
1)
2)
MOD _D EF( 2)appear as N C ( connection) and MOD _D EF(
1:
no
,
0)
is TTL LOW . W hen the host system detects this condition,
it activates the serial protocol (
standard tw o-w ire I
2
C serial
interface) and generates the serial clock signal (
SCL) The
.
positive edge clocks data into the EEPROM segments of the
SFP that are not w rite protected,and the negative edge clocks
data from the SFP.
The serial data signal ( A ) is for serial data transfer. The
SD
host uses SD A in conj
unction w ith SCL to mark the start and
end of serial protocol activation. The supported monitoring
functions are temperature,voltage,bias current,transmitter
pow er,average receiver signal,all alarms and w arnings,and
softw are monitoring of TX Fault/LOS. The device is internally
calibrated.
The data transfer protocol and the details of the mandatory
and vendor specific data structures are defined in the SFP MSA ,
and SFF-8472,Rev. 9.4.
Pow er Supply and G rounding:
The pow er supply line should
be w ell-filtered. A ll 0.1 F pow er supply bypass capacitors
should be as close to the transceiver module as possible.
Oplink Communications,
I
nc.
4
S0115,Rev.02
2010-12-23
TR PC0 3-E 1G Single Mode
Package O utline
41.80
[1.646]
13.62
[.536]
14.94
[.588]
45.00
[1.772]
6.25
[.246]
1.99
[.078]
[.257]
6.54
0.60
[.024]
435 and P y rmont, 958 e (1) 3-20 ax(1) 3-30 mail:ale
63 L ing kw Fe
CA 43 Tl: 0 9370 F : 0 9370 E S s@Oplink. • w .
5
5
com w woplink.
com
[.470]
11.94
[.362]
9.20
10.45
2.29
[.090]
13.80
[.543]
1.49
[.059]
2.50
[.098]
0.60
[.024]
0.45
[.018]
[.411]
D imensions in inches [
mm]
D efault tolerances:
.xxx = ± .005” .xx = ± .01”
,
O rdering I ormation
nf
Part N umber
O perating Tem-
perature
Latch
C olor
Yellow
Red
Yellow
Red
N ominal
W avelength
1310nm
1310nm
1310nm
1310nm
SO N ET/ H
SD
Standards
IR-1/S-1.1
LR-1/L-1.1
IR-1/S-1.1
LR-1/L-1.1
D istance
1
21/15km
50/40km
21/15km
50/40km
TRPC03A I1C000E1G
2
TRPC03EL1C000E1G
TRPC03A I1I000E1G
2
TRPC03EL1I000E1G
1
2
- 5°C to +70°C
- 5°C to +70°C
- 40°C to +85°C
- 40°C to +85°C
These are target distances to be used for classi cation and not for speci cation,per Telcordia G R-253-CORE/ITU -T Recommendation G .957.
The TRPC03A I1C000E1G and TRPC03A I1I000E1G can also be used for short reach SR-1/I-1 applications.
Oplink Communications,Inc. reserves the right to make changes in equipment design or speci cations w ithout notice. Information supplied by Oplink Commu-
nications,Inc. is believed to be accurate and reliable. H ow ever,no responsibility is assumed by Oplink Communications,Inc. for its use nor for any infringements
of third parties,w hich may result from its use. N o license is granted by implication or otherw ise under any patent right of Oplink Communications,Inc.
Freewheeling and snubber diodes Requirements for freewheeling and snubber diodes Modern fast switching devices require the use of fast diodes as freewheeling diodes. During each switch on process, the...
:) Which zigbee module is better in the market? I need to network 2000 nodes, please recommend. Also, I saw a post a long time ago saying that the number of CC2530 networks is relatively small, which ...
:titter: :titter: :titter:
I bought an nRF24L01 chip from Taobao two days ago. After connecting it according to the information provided by the online store (the physical circuit has been tested with ...
The idea is to use TA CCR0 and CCR2 interrupts, change the flag, and then assign values in the main program. The result is that the value obtained from the first sampling is 270, and each subsequent s...
Adopt CS493263 audio DSP, CS8415 96KHz digital receiver, 96KHz/24bit ADC and DAC. Support Dolby Digital AC-3, Dolby Pro Logic, DTS, PCM and other 5.1 channel decoding. STL215 microcontroller can direc...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
Against the backdrop of global warming, energy conservation and emission reduction have become a global hotspot and focus, which has also sounded the clarion call for the take-off of the LED lighti...[Details]
1 Overview
In the field of traditional lighting, the concepts and definitions of lamps and lamps are clear. Lamps and lamps have their own applicable product standards, supporting technical st...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
