will enable the component to operate at its continuous power rating. Thermal grease (e.g. Dow
Corning DC340) should be used and the heatsink should have a surface finish of <6.3μm with flatness of <0.05mm. The resistor should be mounted
using an appropriate bolt as listed in the table below. This should be tightened so as to bring the whole area of the steel substrate into intimate
contact with the heatsink. The unmounted part is slightly bowed so that the centre is above the edges. Inadequate tightening will leave the centre
out of contact with the heatsink, whilst over tightening can cause the edges to rise. The tightening torque required will depend on the fixings and
heatsink used, but typical figures are given for guidance. WDBR resistors will fail safe (open circuit) under overload fault conditions and still maintain
a 1kV dielectric withstand.
Bolt Size
WDBR1/2
WDBR1
WDBR2
WDBR3
WDBR5
WDBR7
M2
M3
M5
M5
M5
M5
Typical Tightening Torque (Nm)
0.6
2
2.5
2.5
3.5
4
WDBR resistors may be customised in various ways including:
Alternative shapes and dimensions up to 406mm x 406mm
Integration of temperature measurement elements
Alternative ohmic values, tolerance & TCR
Increased dielectric withstand voltage
Custom braking resistors with UL approval
For a full Applications Note for dynamic braking see http://www.welwyn-tt.com/pdf/application_notes/WDBR.pdf
·
·
·
·
·
Overload Conditions
Maximum Single Overload Power
100
Power (kW)
Single Overload Energy Capacity
100
Energy (kJ)
10
1
0.1
0.01
0.01
WDBR7
WDBR5
WDBR3
WDBR2
WDBR1
WDBR1/2
10
1
0.1
0.01
W
DB
R
7
W
DB
R
5
W
DB
R
3
W
DB
R
2
W
DBR1
W
DBR1/2
W
0.1
1
10
100
0.1
1
10
100
Duration of Overload (s)
Duration of Overload (s)
Maximum peak current (A)
Value
(ohms)
WDBR1/2
WDBR1
WDBR2
WDBR3
WDBR5
WDBR7
12
15.2
21.6
20.3
25.4
25.4
44.5
15
15.2
21.6
20.3
25.4
25.4
44.5
20
7.6
21.6
7.6
25.4
25.4
44.5
22
7.6
8.3
7.6
25.4
25.4
44.5
25
7.6
8.3
7.6
11.4
25.4
44.5
47
7.6
8.3
7.6
11.4
10.2
20.3
50
7.6
8.3
7.6
11.4
10.2
20.3
100
7.6
8.3
7.6
11.4
10.2
20.3
8.3
7.6
11.4
10.2
20.3
150
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
I would like to ask about the problem in the picture. I used a USB blaster and followed the PDF document in the Black Gold document to restore the factory settings. After installing the software and d...
I inserted two USB flash drives into my computer at the same time. One is identified as a local disk and the other as a removable disk. I don't know why they show different types of storage devices (m...
There is a 4Mhz signal. After passing through the detector diode, how can I filter out the 4MHz and 2nd, 3rd, and 4th harmonics without losing the low-frequency signal below 200K? Please help me, what...
[i=s]This post was last edited by yuanlai2010 on 2014-8-6 12:26[/i] [align=center][font=楷体, 楷体_GB2312][size=5][b][color=#ff0000]System()[/color][/b][b][color=#ff0000]Calling & exec() Function Family[/...
Now it is possible to output to another display screen via USB to serial port or directly via serial port. How should I start with such a solution? What kind of information should I look for?...
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Based on the actual situation, a remote intelligent anti-theft alarm device for home use, connected to the telephone line, simple to operate, and stable and reliable in operation is designed. When ...[Details]
0 Introduction
With the rapid development of modern power electronics technology, various power electronic devices have been widely used in various fields such as power systems, industry, an...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
