EEWORLDEEWORLDEEWORLD

Part Number

Search

IXD2136E44CDR-G

Description
Switching Regulator,
CategoryPower/power management    The power supply circuit   
File Size2MB,26 Pages
ManufacturerIXYS
Environmental Compliance
Download Datasheet Parametric View All

IXD2136E44CDR-G Overview

Switching Regulator,

IXD2136E44CDR-G Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid8000617707
Reach Compliance Codecompliant
ECCN codeEAR99
Analog Integrated Circuits - Other TypesSWITCHING REGULATOR
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Maximum time at peak reflow temperatureNOT SPECIFIED
Product Specification
IXD2135/IXD2136
Synchronous 1A Step-Up DC/DC Converter
FEATURES
Operating Input Voltage Range:
0.65 V ~
6.5 V
Output Voltage Range:
1.8 V~5.0V with
(0.1V increments, accuracy ±2.0%)
Oscillation Frequency:
1.2 MHz ± 15%
Built-in Switching 0.2 Ω NMOSFET
Build-in Synchronous Rectification 0.2 Ω
PMOSFET
Operating Mode:
PWM or PWM/PFM Auto
Selection
Protection:
Over-Current Limit Latch,
Thermal Shutdown
Functions:
Under-Voltage Lockout, Soft
Start, Load Disconnect, Load Capacitor Auto
Discharge,
Operating Ambient Temperature:
-40 -
0
+85 C
Package:
USP-10B (10-pin 2.6 x 2.9 x 0.6
mm)
EU RoHS Compliant, Pb Free
Mobile phones
Cameras, VCRs
Various portable equipment powered from 1
– 3 cell alkaline or 1 cell Li-ion batteries
transistor and a 0.2 Ω synchronous P-channel
transistor capable of providing up to 1.0 A inductor
peak current.
The IXD2135/36 converters are able to start
operation at 0.9 V input voltage to generate 3.3 V
output voltage with a 33 Ω load resistor, which is
suitable for mobile equipment powered from a single
alkaline or nickel metal hydride battery.
The load disconnect function cuts the current
conduction path from input to output at shutdown
mode.
The output voltage is selectable in 0.1 V increments
within 1.8 ~ 5.0 V (± 2.0% accuracy).
The Under-voltage Lockout (UVLO) function prevents
battery damage due deep discharge.
The UVLO threshold voltage is 0.85 V (B/K versions)
or 1.6V A/C versions), and are selectable in the
range from 0.9 V to 3.0 V.
The IXD2135/36 requires only inductor and three
ceramic capacitors connected externally for normal
operations.
Maximum oscillation frequency is set at 1.2 MHz in
PWM mode and maximum duty cycle is set at 93%,
making it suitable for use with large load current. The
IXD2135/36 converters are able to switch
automatically between PWM and PFM modes to
support both large and small load currents.
These IXD2135/36 converters use small 10-pin 2.6 x
2.9 x 0.6 mm USP-10B packages.
APPLICATION
DESCRIPTION
The IXD2135/36 are synchronous step-up DC/DC
converters with build-in a 0.2 Ω N-channel switching
TYPICAL APPLICATION CIRCUIT
TYPICAL PERFORMANCE CHARACTERISTIC
Efficiency vs. Output Current
IXD2135C32CDR-G (V
OUT
=3.2V)
L = 4.7 μH (VLF3014ST-4R7M1R1), C
L
= 22 μF (LMK316ABJ226ML), C
IN
= 10 μF (JMK212ABJ106KG),
C
DD
= 0.47 μF (TMK107BJ474KA) f
OSC
=1.2MHz
PS036201-0615
PRELIMINARY
1
Huawei Hardware Engineer Manual..pdf Free!!!
.Huawei Hardware Engineer Manual..pdf Free!!!...
linda_xia Analog electronics
[Xilinx Technical Q&A] What is the actual operating frequency of FPGA?
The synthesis report and static timing analysis report given in the ISE software both have operating frequencies. Which one is the actual operating frequency of the FPGA? A: The frequency value after ...
eeleader FPGA/CPLD
[RISC-V MCU CH32V103 Review] - 9: Motor Control Board
[i=s]This post was last edited by MianQi on 2021-3-17 10:56[/i]This test: [RISC-V MCU Application Development]Chapter 80, CH32V103 Application Tutorial - DC Brushed Motor Key Control Website: https://...
MianQi Domestic Chip Exchange
Raspberry Pi Windows IoT Development (Part 2) USB Camera
Table of contentsRaspberry Pi Windows IoT Development (Part 1) Raspberry Pi Windows IoT Development (Part 2) USB Camera Raspberry Pi Windows IoT Development (Part 3) Flashing LED Raspberry Pi Windows ...
bigbat Embedded System
Help with problems when drawing PCB
When drawing a PCB, I want to allow the middle part of the figure below to be able to place devices, but not the ring part, that is, when the device is placed in the ring area, it will turn green and ...
sunagun PCB Design
Electronics competition trial broadband amplifier design help
I'm making a broadband amplifier recently with 0-8M input and the requirement is to amplify 10,000 times. I'm considering a three-op-amp instrument amplifier circuit, but I can't find a suitable ampli...
needhelp Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2826  672  760  2210  1855  57  14  16  45  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号