EEWORLDEEWORLDEEWORLD

Part Number

Search

Z-01H2W2277-B

Description
Snap Acting/Limit Switch,
CategoryMechanical and electronic products    switch   
File Size7MB,28 Pages
ManufacturerOMRON
Websitehttps://www.omron.com
Download Datasheet Parametric View All

Z-01H2W2277-B Overview

Snap Acting/Limit Switch,

Z-01H2W2277-B Parametric

Parameter NameAttribute value
Objectid7067957789
Reach Compliance Codeunknown
ECCN codeEAR99
Manufacturer's serial numberZ
Switch typeSNAP ACTING/LIMIT SWITCH
General-purpose Basic Switch
Z
CSM_Z_DS_E_4_4
Best-selling Basic Switch Boasting
High Precision and Wide Variety
• A large switching capacity of 15 A with high repeat accuracy.
• A wide range of variations in contact form for your selection: basic,
split-contact, maintained-contact, and adjustable contact gap types.
• A series of standard models for micro loads is available.
• A series of molded terminal-type models incorporating safety
terminal protective cover is available.
Be sure to read
Safety Precautions
on page 26 and
Safety Precautions
for All Basic Switches.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Model Number Structure
Configuration
Basic models
General-purpose
Drip-proof
Without terminal protective cover
With terminal protective cover
Molded terminal
Split-contact models
Maintained-contact models
General-purpose
General-purpose
Refer to page 3.
Refer to page 5.
Refer to page 5.
Refer to page 2.
Refer to page 4.
Refer to page 4.
Basic Models
General-purpose
A variety of actuators is available for a wide range of application.
The contact mechanism of models for micro loads is a crossbar
type with gold-alloy contacts, which ensures highly reliable
operations for micro loads.
Contact Gap:
H2: 0.20 mm (extra-high-sensitivity)
H: 0.25 mm (high-sensitivity, micro voltage current load)
G: 0.5 mm (standard)
E: 1.8 mm (high-capacity)
Split-contact Models
This type is identical in construction to the general-purpose basic
switch except that it has two pairs of simultaneous acting contacts
by splitting moving contacts.
Since the moving contacts are connected to a common terminal,
either parallel or series connection is possible.
Highly reliable micro load switching is ensured if the model is used
as a twin-contact switch.
Maintained-contact Models
The maintained-contact type has a reset button at the bottom of the
switch case, in addition to the pushbutton (plunger) located on the
opposite side of the reset button. Use these buttons alternately.
Since the Switch has greater pretravel than overtravel, it is suitable
for use in reversible control circuits, manual reset circuits, safety
limit circuits, and other circuits which are not preferable for
automatic resetting. (For further details, refer to individual
datasheets.)
Drip-proof
These Switches use a rubber boot on the actuator and adhesive fill
between the case and cover to increase resistance to drips.
Models with drip-proof terminal protective covers and molded
terminals with resin filling are also available.
1
AVR--DIY activity call post
The AVR section has not been active for a long time. I think everyone is very busy, but time is really squeezed out. Here I launch an avr--diy activity. If you have any good suggestions, feel free to ...
鑫海宝贝 Microchip MCU
Can TMS320C6455 connect to two RJ45 plugs at the same time?
I recently encountered a problem. When using TMS320C6455 for Ethernet design, I want to connect two RJ45s at the same time through a TMS320C6455 through a PHY chip. According to the manual, TMS320C645...
cyh19890727 DSP and ARM Processors
Electronic design materials
[i=s]This post was last edited by paulhyde on 2014-9-15 09:44[/i]doc...
yelinyimeng Electronics Design Contest
(Update) TI MSP430F5529 training [Study with Gifts] The fourth round of award information is announced!
[font=微软雅黑]Due to the error in the statistics of this issue, the technical staff has re-counted the data. Comprehensively evaluated [color=#0000ff][b]hellocutegirl[/b][/color][color=#000] won[/color][...
EEWORLD社区 Microcontroller MCU
After current sampling, the inverted ratio is amplified by 2 times (U9A), and then the output is connected to the form of a hysteresis comparator (U9B), which is...
After the current is sampled, it is inverted and amplified by 2 times (U9A), and then the output is connected to the form of a hysteresis comparator (U9B). Why can't it be directly fed to the ADC port...
QWE4562009 Discrete Device
Still don't know how to burn NORFLASH
I am using the STM3210E-EVAL evaluation board. I want to put some tables and arrays in the program into NOR FLSAH, but I don't know how to burn them in. Please give me some advice if you know how....
漂叶 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1451  2289  960  1478  2863  30  47  20  58  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号