MCU model: STC89LE516RD+. PFP package. Phenomenon: Occasionally, it does not work after power on. After that, I turned off all the power and turned it on again, but it still does not work. I turned of...
Today, I used FPGA to read and write internal ROM. After carefully studying the ROM timing, I found that: for ROMs without output latches, after giving the address, valid data is retrieved after a del...
I recently made a board. When I connected it to the emulator, the emulator light turned red. It uses the STM32F103CB chip. I don't know what the problem is. Please help me check it out.103cbdl.jpg(56 ...
PCB drilling is a process of PCB plate making, and it is also a very important step. It is mainly to punch holes in the board. For routing needs, a via is needed. For structural needs, a hole is drill...
[i=s] This post was last edited by paulhyde on 2014-9-15 09:44 [/i] The test questions recommended by the organizing committee of the 2009 National Competition Guangxi Division Selection Competition a...
China's photovoltaic power generation installed capacity achieved rapid growth in 2017, and distributed photovoltaics achieved explosive growth. In 2017, the country's photovoltaic installed capaci...[Details]
Event: The company simultaneously released its 2017 annual report and the first quarter report of 2018. In 2017, the company achieved revenue of 8.886 billion yuan, a year-on-year increase of 48.01...[Details]
1. Principle 1. Infrared emission protocol The infrared transmission protocol has been written in the previous article , so I will not repeat it here. 2. Timer counting and input capture A timer...[Details]
1. Placement suspension void NVIC_Configuration(void) { NVIC_InitTypeDef NVIC_InitStructure; /* Set the Vector Table base location at 0x08004000 NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x4000)...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Processors with artificial intelligence are mostly integrated into cars, PCs, security cameras, smart speakers, robots and other related technology equipment, but
AI
chips were initially de...[Details]
Every era has its own representative company, and the small game between representative companies in the big era also reflects the big game between countries to a certain extent. Let's learn about ...[Details]
Autonomous driving
and
5G
are the two hot topics that global companies and media are paying the most attention to, and the combination of the two is the focus of everyone's attention....[Details]
Many embedded geeks are wondering what the future holds if they continue to invest time, energy and money in MICroChip's PIC32 series MCUs. Will their investment be safe, and how does it compare ...[Details]
STM32 has two watchdogs: independent watchdog and window watchdog. This article mainly introduces the use of independent watchdog. Independent watchdog (IDWG): driven by an independent 40KHZ low-sp...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
In the 80C51 single-chip microcomputer, the clock frequency is known to be 6MHz. Please program P1.0 and P1.1 to output square waves with periods of 2s and 0.5s respectively. Please give the answer a...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
