EEWORLDEEWORLDEEWORLD

Part Number

Search

CTR3120ACJCGGNKWS

Description
Array/Network Resistor, Center Tap, Thin Film, 312ohm, 100V, 0.25% +/-Tol, -50,50ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size93KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

CTR3120ACJCGGNKWS Overview

Array/Network Resistor, Center Tap, Thin Film, 312ohm, 100V, 0.25% +/-Tol, -50,50ppm/Cel, 0303,

CTR3120ACJCGGNKWS Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid958046885
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
JESD-609 codee4
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingWaffle Pack
resistance312 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTR
size code0303
technologyTHIN FILM
Temperature Coefficient-50,50 ppm/°C
Terminal surfaceGold (Au)
Tolerance0.25%
Operating Voltage100 V
CTR
Vishay Electro-Films
Thin Film, Center-Tapped Resistors
CHIP
RESISTORS
FEATURES
Product may not
be to scale
The CTR series is a center-tapped resistor chip combining
excellent stability with 250 mW power levels. The CTR offers
the designer flexibility in use as either a single value resistor
as two resistors with a center tap feature. The CTR’s six
bonding pads allows the user increased layout flexibility.
The CTRs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTRs are 100 % electrically tested and
visually inspected to MIL-STD-883.
Wire bondable
Center tap feature
Tight ratio tolerances to: 0.05 %
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Oxidized silicon substrate for good power dissipation
Resistor material: Tantalum nitride, self-passivating
Moisture resistant
I
V
R
A
R
B
V
I
V
APPLICATIONS
Vishay EFI CTR center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power
and tracking between two resistors is critical.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique. The method illustrated above is critical for resistors
of less than 100
Ω.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
10
Ω
25
Ω
100
Ω
360 kΩ 620 kΩ
1 MΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, < 100
Ω
or > 251 kΩ
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Note
(1)
5 ppm/°C for
R
< 100
20 ppm/°C for
R
< 20
www.vishay.com
78
For technical questions, contact:
efi@vishay.com
Document Number: 61020
Revision: 17-Aug-09
± 2 ppm/°C
(1)
1 ± 1 % standard
- 20 dB typ.
± 0.5 % max.
ΔR/R
± 0.2 % max. absolute
- 55 °C to + 125 °C
± 0.1 % max.
ΔR/R
± 0.2 % max.
ΔR/R
200 V
10
12
min.
100 V max.
250 mW
± 0.1 % max.
ΔR/R
Asking for help: G2553 simulation problem
Why is it fine during simulation? But when I disconnect the simulation and reset it, it fails. Why is this? Is there any special processing during simulation?...
成都回锅肉 Microcontroller MCU
Compact W600 development board
I got the W600 development board, it is very small....
dcexpert MicroPython Open Source section
How to write a server thread to accept client requests under EVC
I am a novice and don't know much about the specific operation of threads. Can anyone help me? Thank you....
bigfatty Embedded System
【Teaching Embedded Linux from Scratch】Episode 18
Lesson 18: How to make your own application start automatically at boot 1. First copy our own application to the development board, for example: /led_test 2. According to the startup script /etc/init....
babyking Embedded System
Has anyone developed network card drivers under ICH8/ICH9?
I can't find the document Intel ICH8/ICH9 (MAC) GbE LAN Controller and 82566/82562V (PHY) Software Developer's Manual. I can't find it on Intel's official website. Does anyone have one? Can you share ...
polestar707 Embedded System
Control WIFI under WINCE
Hi All, I have a project that I want to use a program under WINCE to control the start/stop of WIFI, automatically select AP, and set the WEB/WAP key without user intervention. How can I do this? Can ...
xfzj1314 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2052  1079  2861  908  476  42  22  58  19  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号