EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3S272BC-0063CD8

Description
LVPECL Output Clock Oscillator
CategoryPassive components    oscillator   
File Size473KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance  
Download Datasheet Parametric View All

8N3S272BC-0063CD8 Overview

LVPECL Output Clock Oscillator

8N3S272BC-0063CD8 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1320159630
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TR
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
JESD-609 codee3
Installation featuresSURFACE MOUNT
Nominal operating frequency24 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVPECL
Output load50 OHM
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry53/47 %
Terminal surfaceMatte Tin (Sn)
LVPECL Frequency-Programmable
Crystal Oscillator
IDT8N3S272
DATA SHEET
General Description
The IDT8N3S272 is a Frequency-Programmable Crystal Oscillator
with very flexible frequency programming capabilities. The device
uses IDT’s fourth generation FemtoClock® NG technology for an
optimum of high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm package.
The device can be factory programmed to any frequency in the range
from 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommun- ication and networking end equipment
requirements.
Features
Fourth generation FemtoClock® NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V or 3.3V LVPECL clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.24ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.27ps (typical),
integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
Pin Assignment
DNU
1
2
3
6
5
4
V
CC
nQ
Q
nOE
V
EE
OSC
f
XTAL
2
÷P
÷N
Q
nQ
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N3S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N3S272CCD
REVISION A NOVEMBER 28, 2012
1
©2012 Integrated Device Technology, Inc.
SDRAM read and write problems
In the sdram read and write test, I referred to the privileged classmate's program. In the data_gen module: reg wr_done; //All data written to sdram completion flag always @(posedge clk or negedge rst...
ole007 FPGA/CPLD
【Low power consumption】 Xilinx PCB specification
Four- and six-layer high-speed PCB designs for the Spartan-3E FT256 BGA package....
dream_byxiaoyu FPGA/CPLD
My usart serial port cannot receive data using the serial port assistant
The configuration is as follows GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPD; //Pull-up input GPIO_Init(GPIOB, &GPIO_InitStructure); GPIO_InitStructure.GPIO_...
乱起东城 stm32/stm8
Serial port cannot be used under WINCE
Please help me, my serial port 1 is used for debugging in wince, and now I can't use the application in the system. How can I modify the bsp so that my serial port can be called by the application? Th...
sjh008 Embedded System
Suggestions for college students to learn ARM and FPGA (reprint)
[color=#0000ff]"Suggestions for college students to learn ARM and FPGA" Source: Zhou Ligong's blog[/color] For beginners, there are many knowledge points to learn. People often feel very confused abou...
ptwang ARM Technology
Problems with soldering of microcontroller development board
I use ATMEL89C52~~This is the schematic diagram [img]http://p13.freep.cn/p.aspx?u=v20_p13_p_0910310829314162_0.gif[/img]. I don't know which part is used for power supply and burning program. If not, ...
etual1983 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1977  2863  1334  1968  2817  40  58  27  57  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号