EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S272BC-0077CDI8

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size599KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

8N4S272BC-0077CDI8 Overview

LVDS Output Clock Oscillator

8N4S272BC-0077CDI8 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1308557482
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TR
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
Installation featuresSURFACE MOUNT
Nominal operating frequency125 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry53/47 %
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S272
DATA SHEET
General Description
The IDT8N4S272 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
DNU 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
nOE 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S272CCD
REVISION A OCTOBER 3, 2012
1
©2012 Integrated Device Technology, Inc.
[Sipeed LicheeRV 86 Panel Review] 4-Transplanting lvgl-Adding touch control
In the previous review, we implemented the transplantation of lvgl, and we can add controls to change the display function. But how can a touchpad be without the touch function? Therefore, we need to ...
manhuami2007 Domestic Chip Exchange
[Ask TI] How to stabilize the output with wide voltage input
The input voltage of solar power supply fluctuates between 2-9V, and the internal resistance of the power supply is relatively large. In this case, how to output 5V voltage stably? [[i] This post was ...
leang521 Analogue and Mixed Signal
Is there a book called "Two-color illustrations and detailed explanation of capacitors and application circuits"?
Is there a book called "Two-color illustrations and detailed explanation of capacitors and application circuits"?...
electrical93 Analog electronics
Protel Tutorial
[i=s]This post was last edited by paulhyde on 2014-9-15 03:57[/i] Prepare for the next one and start with the basics!...
孤单南极 Electronics Design Contest
[Help] SIM300C sleep problem, why can't it connect to GPRS after sleep?
I am a novice, I hope you experts can help me~~~ I use SIM300C to transmit data via GPRS. After transmitting data once, I set the DTR pin to high level (the manual says that this can sleep). After tha...
z2661213 Embedded System
I would like to ask why the b ResetHandler in 44binit.s in S3C44b0 cannot jump
Hello everyone, I created a new project and added files on the S3C44b0 development board, and then compiled and simulated through ADS. As a result, I found that there was no response on the developmen...
rocky_z ARM Technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1613  1238  2639  2522  219  33  25  54  51  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号