3) Electrodes not corroded by soldering Thick film makes
the electrodes very strong.
4) Leading the world in development and mass produc-
tion.
Since start of production in 1976 (first in the wold),
this component has established a solid reputation as
a general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certifica-
tion.
Design and specifications are subject to change with-
out notice. Carefully check the specification sheet be-
fore using or ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70
°
C.
100
80
60
40
20
0
Specifications
0.25W (1 / 4W)
at 70
°
C
POWER LOAD (%)
−55
0
70
100
155
AMBIENT TEMPERATURE (
°
C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E= P
×
R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55
°
C
to + 155
°
C
Max. intermittent overload voltage
400V
Max. operating voltage
200V
Max. overload voltage
400V
MCR18
Resistors
Jumper type
Resistance
Rated current
Peak current
Max. 50mΩ
2A
10A
F ( ± 1%)
Table 1
Resistance tolerance
Resistance range
(Ω)
10
≤
R
≤
2.2M
1.0
≤
R
<
2.2
J ( ± 5%)
2.2
≤
R
<
10
10
≤
R
≤
10M
(E24,96)
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm /
°C)
± 100
500 ± 350
± 500
± 200
Operating temperature
−55°
C
to + 155
°
C
!
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high–level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it
is used with a steady state voltage that is greater than its rated voltage.
MCR18
Resistors
!Characteristics
Characteristics
DC resistance
Resistance temperature
characteristics
Short time overload
± (2.0% + 0.1Ω)
Specifications
Chip resistance
Jumper type
F: ± 1%
J: ± 5%
Max. 50mΩ
Test method
JIS C 5202 5.1
Applied voltage: A
JIS C 5202 5.2
Test conditions: + 25 /
−55
/ + 25 / + 125°C
JIS C 5202 5.5
Rated voltage (current):
×
2.5, 5s.
Maximum overload voltage: 400V
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
See Table 1.
Max. 50mΩ
Min. 1,000MΩ between terminal and board
Insulation resistance
Test resistor
Metal plate
Observation Insulation
sheath
R 0.5
point B
Spring-loaded
pressure
Withstand voltage
Do not damage insulation or cause a short circuit.
JIS C 5202 5.7
Test voltage: 500V
JIS C 5202 5.8
Rated voltage (current):
×
2.5
(1s: ON
−
25s: OFF)
×
10,000cyc.
JIS C 5202 6.1
JIS C 5202 6.4
Soldering conditions: 260 ± 5°C
Soldering time: 10 ± 1s.
JIS C 5202 6.5
Rosin methanol: (25%WT)
Soldering conditions: 235 ± 5°C
Soldering time: 2.0 ± 0.5s.
JIS C 5202 7.2
155°C
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current), 70°C
1.5h: ON
−
0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current), 60°C, 95%RH
1.5h: ON
−0.5h:
OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85°C, 85%RH
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.4
Test temperature:
−55°C
to + 125°C 100cyc.
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Intermittent overload
Terminal strength
(against bending of circuit board)
Resistance to soldering heat
± (5.0% + 0.1Ω)
Max. 50mΩ
± (1.0% + 0.05Ω)
Max. 50mΩ
There must be no mechanical damage.
± (1.0% + 0.05Ω)
Max. 50mΩ
Outside must not be noticeably damaged.
95% of terminal surface must be covered by
new soldering, and there must be
no soldering corrosion.
Solderability
Resistance to dry heat
± (3.0% +0.1Ω)
Max. 100mΩ
Endurance
(rated load)
± (3.0% +0.1Ω)
Max. 100mΩ
Endurance
(under load in damp environment)
± (3.0% +0.1Ω)
Max. 100mΩ
Resistance to humidity
(steady state)
± (3.0% +0.1Ω)
Max. 100mΩ
Temperature cycling
± (1.0% +0.05Ω)
Max. 50mΩ
Resistance to solvents
± (0.5% +0.05Ω)
Max. 50mΩ
Markings must not be dissolved away.
MCR18
Resistors
!External
dimensions
(Units: mm)
0.5 ± 0.25
No.
Material
Thick dielectric glaze of ruthenium (only silver used for jumper)
Thick film of palladium-silver for primary electrode
3.2 ± 0.15
0.55 ± 0.1
0.5 ± 0.25
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
Overcoating
!Packaging
Reel
Taping
P
0
P
2
P
2
φD
2
E
F
B
2
08
06
04
02
02
04
06
08
1.6 ± 0.15
W
A
B
D
A
2
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
"Love is too deep, scars are easily visible; love is too true, so it is hard to let go. Fold a thousand pairs of paper cranes to express a thousand emotions... A thousand paper cranes and a thousand h...
According to official information, there are three ways to compile Linux servers : virtual machines, cloud servers, and PC servers. Linux development has always used a pure Linux environment on the X8...
A netizen in Shijiazhuang wanted this circle to teach you how to play USB. I happened to have it on hand, so I uploaded it today and shared it with everyone. This is a USB development board made by so...
Last Friday, I received the xmc4800kit from the eeworld forum, but I haven't had time to review it since I went home for the New Year holiday. I'm really sorry. Today, I'll post an unboxing post as us...
[size=3][font=宋体]Every week I get a lot of emails from people who want to make a robot. Usually they want to make it with simple components, either from home or from hardware stores. As a robot maker ...
Today the outside is yellow, or rather orange, and there was such a thick fog when I woke up in the morning. I don't think I've ever seen such weather. Did 2012 come early? Or was it a sandstorm? Take...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
Flip-chip and ball grid array (BGA) are two widely used packaging technologies in the electronics industry. Each has its own advantages and limitations, and in some cases, they can complement each ...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
Multi-touch mobile phone
Multi-touch is a system that can respond to multiple touches on the screen at the same time. Multi-touch phones are divided into capacitive and resistive types. Capaci...[Details]
Logic analyzers are widely used tools in digital design verification and debugging. They can verify the proper functioning of digital circuits and help users identify and troubleshoot faults. They ...[Details]
According to foreign media reports, BMW has just been granted a patent for a screen that could cover the entire roof. BMW hopes to transform at least a portion of the vehicle's headliner into a dis...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
As AI accelerates across industries, the demand for data center infrastructure is also growing rapidly.
Keysight Technologies, in collaboration with Heavy Reading, released the "Beyo...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
Creative Market
京公网安备 11010802033920号
EEWORLD
