EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AS-03-4871-BG

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 4870ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AS-03-4871-BG Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 4870ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AS-03-4871-BG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802657223
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance4870 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
Some of my simple DIY (first work) hehe
1. Logic PenThis is very powerful when used with an oscilloscope to adjust digital circuits Schematic3D EffectPCB Make it2. A small power supply that converts 1.5V to 9V (max IC is too expensive to bu...
ch0721 DIY/Open Source Hardware
How to assign initial value to capacitor in ORCAD?
:( I just learned to use Orcad's Capture to draw a simple chua circuit, but there is no excitation in the circuit. I can only assign initial values of voltage and current to the capacitor and inductor...
cleverxue PCB Design
A small driver problem for beginners, please help
In embedded drivers, why should the key driver be changed to the input subsystem, and why should the input subsystem be changed to the platform bus architecture? What are the benefits?...
wrf346984243 ARM Technology
Automatic control of matlab - Bode plot
You may find it useful in the theory of automatic control, suitable for reference in automation and related majors! I learned all of it by myself, in order to deepen my understanding of the course at ...
gaoxiao Microcontroller MCU
Apply for an LPC1114 for driver experiment
Apply for an LPC1114 to do driver experiments, :), prepare to make a three-loop driver ~ with SCI, PWM, stepping control modeResource planning and implementation: Resource requirements: ENCODER encode...
longye199035 NXP MCU
Cadence Tool Introduction
1. Logic design and verification tools * Logic simulation tools: Cadence NC-Verilog, Verilog-XL, NCSim, Simvision Waveform Viewer * Synthesis tools: Cadence BuildGates * Formal verification tools: Ver...
ys3663391 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2797  1333  2717  2885  1078  57  27  55  59  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号